JVC G-code ShowView HR-S5900AM Instructions Manual page 55

SELECT TV SYSTEM
5
Press % fi to
PU SH JO G
place the pointer next to
the appropriate TV system,
then press or
O K PU SH
# .
JO G
● Auto Channel Set will
start.
● "M" appears with
HR-S5900AM only.
AUTO CH SET
PLEASE WAIT
START
RETURN TO N O RMAL
SCREEN
6
Press .
M EN U
N O TE:
If you perform Auto Channel Set when the aerial cable is not
connected properly, "SCAN COMPLETED -NO SIGNAL-"
appears on the screen in step
of the aerial connection and press
take place again.
IM PO RTAN T
● If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by
Auto Channel Set, the TV system setting for those
channels may be incorrect. Select the appropriate TV
system for those channels.
When you see the picture but the audio can't be heard or
sounds unnatural" on page 57.
● Since your video recorder memorizes all detected
stations even if the reception condition is poor, some of
those stored stations may produce a noisy picture. To
delete those stations,
M ajor Countries / Areas
Australia, New Zealand, Kuwait, U.A.E.,
Indonesia, Singapore, Thailand, Malaysia,
Iran, Saudi Arabia, Egypt, Morocco,
Lebanon, Iraq
China, Mongolia, Russia
Hong Kong
U.S.A., Japan, S.Korea, Taiwan
*HR-S5900AM only
TV SYSTEM SELECT
B/G
D/K
I
M
[5/ ∞ ] =
[MENU] : EXIT
CH FRQ SYS CH FRQ SYS
01 150 BG 07
02 165 BG 08
03 195 BG 09
04 205 BG 10
05 213 BG 11
06 221 BG 12
FINISH
[5/ ∞ ] = [ ] : DELETE
[5/ ∞ ] = : EDIT
[MENU] : EXIT
. When this happens, make sure
5
; Auto Channel Set will
O K
"TV System Selection –
"Delete A Channel" on page 56.
TV System
B/G
D/K
I
M*
M a nua l Cha nnel Set
Store channels that were not stored during Auto Set Up (
or Auto Channel Set (
ACCESS TUN ER SET
SCREEN
1
Perform steps
ACCESS CHAN N EL LIST
229 BG
237 BG
2
Press
PU SH JO G
355 BG
EDIT", then press
365 BG
374 BG
384 BG
SELECT PO SITIO N
3
Press
PU SH JO G
open channel position, then press
SELECT BAN D
4
Press
PU SH JO G
band of your choice, then press
Channel Set.
[5/ ∞ ] =
[MENU] : EXIT
SET DESIRED ST ATIO N
5
The screen to the right
appears when a station is
detected.
If you do not want to store
the detected station...
Press
PU SH JO G
place the pointer next to
"CONTINUE", then press
or
O K
Channel search will resume.
If you want to store the detected station...
Press
PU SH JO G
"STORE", then press
List appears again.
● The blueback screen and the TV picture currently
being broadcast appear alternately for 8 seconds each.
● If you want to store another channel, repeat steps
● When channel search completes for that band, the
Band Select screen appears again. To set channels for
other bands, select another band and start Manual
Channel Set again (
● For fine tuning adjustment, see "Fine-Tuning
Channels" on page 57.
RETURN TO N O RMAL
SCREEN
6
Press
M EN U
pg. 54).
– of "Auto Channel Set" on page 54.
1 3
%fi to place the pointer next to "CH
or
O K PU SH JO G
%fi to place the pointer next to an
%fi to place the pointer next to the
O K
BAND SELECT
VHF L
VHF H
UHF
[MENU] : EXIT
%fi to
[5/ ∞ ] =
[MENU] : EXIT
# .
PU SH JO G
%fi to place the pointer next to
or
O K PU SH JO G
step and
4
.
55
EN
pg. 8)
# .
or # .
O K PU SH JO G
to initiate Manual
MANUAL CH SET
PLEASE WAIT
VHF L 100MHZ
STORE
CONTINUE
. The Channel
– .
3 5
).
5