Briggs & Stratton 190000 Operator's Manual page 6

Start the Engine
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See
a doctor. You may have carbon monoxide poisoning.
• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
• DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and windows
for ventilation. After the operation of this product, carbon monoxide can quickly
collect in these spaces and stay for hours.
• ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you start the engine
• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are
correctly installed.
• Do not crank the engine with the spark plug removed.
• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
• If there is natural or LP gas leakage in the area, do not start the engine.
• Because vapors are flammable, do not use pressurized starter fluids.
WARNING
Rotating parts can entangle hands, feet, hair, clothing, or accessories and result
in traumatic amputation or laceration.
• Operate equipment with the guards correctly installed.
• Keep hands and feet away from rotating parts.
• Remove jewelry and make sure that long hair is away from all rotating parts.
• Do not wear loose clothes or items that could become caught.
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go. Broken bones, fractures, bruises or sprains
could result.
• To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
• Before you start the engine, disconnect or remove all external equipment and
engine loads.
• Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
1. Check the engine oil. Refer to the Check the Oil Level section.
2. Make sure that the equipment drive controls, if equipped, are disengaged.
3. Push the stop switch (A, Figure 7), if installed, to the ON position.
4. Move the throttle control (B, Figure 7), if installed, to the FAST position. Operate the
engine in the FAST position.
5. Move the choke control (C, Figure 7) to the CHOKE position.
NOTICE The choke is usually not necessary when you start a warm engine.
6. Move the fuel shut-off (D, Figure 7), if installed, to the OPEN position.
7. Rewind Start, if installed: Tightly hold the starter cord handle (E, Figure 7). Pull
the starter cord handle slowly until resistance is felt, then pull quickly.
8. Electric Start, if installed: Turn the electric start switch (F, Figure 7) to the ON or
START position.
9. As the engine warms, move the choke control (C, Figure 7) to the RUN position.
6
Stop the Engine
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
• Do not choke the carburetor (if equipped) to stop the engine.
1. Stop Switch, if installed: Move the stop switch (A, Figure 8) to the STOP position.
2. Throttle Control, if installed: Move the throttle control (B, Figure 8) to SLOW and
then to the STOP position.
3. Electric Start, if installed: Turn the electric start switch (F, Figure 8) to the OFF /
STOP position.
4. Remove the key, and keep it in a safe location.
5. After the engine stops, move the fuel shut-off (D, Figure 8), if installed, to the
CLOSED position.
Maintenance
Maintenance Information
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if
mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not
empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted
in a different direction, it will not easily start because of oil or fuel contamination of the air
filter or the spark plug.
WARNING
Accidental engine spark can cause an electric shock, fire or explosion and could
result in entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
• Disconnect all spark plug wires and keep them away from the spark plugs.
• Disconnect the battery wire from the negative battery terminal (only engines with
electric start).
• Use only the correct tools.
When you check for spark:
• Use an approved spark plug tester.
• Do not check for spark with the spark plug removed.
WARNING
Replacement parts must be of the same design and installed in the same position as the
original parts. Other parts could result in damage or an injury.
NOTICE
All the components used to build this engine must remain in place for correct operation.
See a Briggs & Stratton Authorized Service Dealer for all maintenance and servicing of
the engine and engine parts.
Emissions Control Service
For maintenance, replacement, or repair of emissions control devices and
systems, contact a qualified off-road engine repair establishment or service
technician. However, for "no charge" emissions control service, the work must be done
by a factory authorized dealer. Refer to the Emissions Control Statements.
Maintenance Schedule
First 5 Hours
• Change the engine oil.
Intervals of 8 Hours or Daily
• Check the engine oil level.
• Clean the area around the muffler and controls.
• Clean the air intake grille.
Intervals of 25 Hours or Annually
•
1
Clean the air filter .
•
1
Clean the pre-cleaner .