Related Manuals for Hyundai HCOMBIBP50-A
Summary of Contents for Hyundai HCOMBIBP50-A
- Page 1 ORIGINAL INSTRUCTIONS >EN GASOLINE MULTI TOOL KIT HCOMBIBP50-A INSTRUCTION MANUAL CAUTION: Read the instructions before using the machine!
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS ..........................3 YOUR PRODUCT .............................15 ASSEMBLY...............................17 FILLING OIL TANK AND FUEL TANK ....................22 OPERATION .............................23 MAINTENANCE ............................27 STORAGE ..............................31 DISPOSAL AND RECYCLING .........................31 TROUBLESHOOTING ..........................32 DECLARATION OF CONFORMITY .....................33 WARRANTY ............................34 PRODUCT FAILURE ..........................35 WARRANTY EXCLUSIONS .........................36... -
Page 3: Safety Instructions
1.SAFETY INSTRUCTIONS Safety instructions for brushcutter and grass trimmer Proper safety precautions must be observed. This unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read and understand the machine manual and are trained in its operation. - Page 4 of any other accessories or attachments may cause injuries to the user, damage to the machine and void this warranty. When refuelling, be sure to stop the engine and confirm that it is cooled down. Never refuel when the engine is running or hot.
- Page 5 Clean and maintain the tool before storage (see the chapters on this manual). Bring maintenance after each use according the instructions of this manual. Improper maintenance can reduce the lie of the tool, bring bad results and wear the tool and its accessories. ...
- Page 6 Contact with projected objects Burns when touching with hot surfaces Prolonged use of this product exposes the operator to vibration and can produce so-called "white finger" disease. To reduce the risk, wear gloves and keep your hands warm. If any of the symptoms of "white finger syndrome" occur, seek immediate medical attention. Symptoms of the "white finger"...
- Page 7 plug and take the following steps: inspect for damage; check for, and tighten, any loose parts; have any damaged parts replaced or repaired with parts having equivalent specifications h) Wear ear protection. Wear eye protection. In case of emergency, stop the hedge trimmer; release the trigger, switch off the tool with the ON/OFF button.
- Page 8 When a danger or a non-intended situation arise, stop to work immediately and switch off the tool. Restart to work when there is no danger and you can work safely. Cut before the large branches with a hand shears to avoid the blocking of the blade. ...
- Page 9 Safety warnings for the mounted pole pruner Proper safety precautions must be observed. This unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read and understand the machine manual and are trained in its operation.
- Page 10 before starting the engine. Stay clear of other workers or bystanders by at least 15 meters. Whenever approaching an operator of the machine, carefully call his attention and confirm that the operator stops the engine. Be careful not to startle or distract the operator which can cause an unsafe situation.
- Page 11 cracks in the cutting attachment. If the tool is damaged, if parts are missed or meet some dysfunctions, do not use the tool and bring it to a service agent for inspection and reparation. Check the tool after dropping or other impacts to identify any significant defects; if any defects are observed, stop to use the tool and bring it to a service agent for inspection and reparation.
- Page 12 wrists. Risk increases at low temperatures Inhalation of particles Inhalation of exhaust gases Unattended projections Contact with foreign objects Contact with the tool in operation Hearing loss in the absence of correct hearing protection To minimize those risks, follow the instructions of this manual about wearing personal equipment of protection, take some rest during the operation and the manipulation of the tool.
- Page 13 Wear eye protection Wear protection gloves Wear hearing protection Wear protective footwear Caution to exhaust gases Caution – Risk of fire Do not smoke and do use the tool near naked flame The accessible part are hot when operate the tool Caution! Risk of rebound...
- Page 14 Warning – Risk of electric shock. Always beware of the danger from overhead electric- power line, keep a safe distance at least 10m from the power line Caution! The tool can contact to a voluminous material. Loss of control and injuries can be created.
-
Page 15: Your Product
2. YOUR PRODUCT a. Description 1) Motor drive unit 11) Throttle lever 18) Carter of protection for 2) Pole saw 12) Oil tank for chain saw brushcutter and grass 3) Tube 13) Saw chain trimmer 4) Brushcutter/grass trimmer 14) Chain saw blade 19) Spark plug wrench head 14a) Saw blade cover... - Page 16 c. Technical data Engine displacement 52 cm Maximum engine speed 9500min-¹ Maximum power 1,45 kW 7500/min Mass Max. 7.91 kg Volume of fuel tank 1200 cm Type: 2 lines (non-metallic flexible line) Cutting diameter: 430mm Grass trimmer Cutting thickness: 2,5 mm Type: single piece (three teethes metal) Brush cutter Cutting diameter: 255mm...
-
Page 17: Assembly
3. ASSEMBLY When assembling, put on protective gloves. Blades can be sharp. a. Mounting the flexible shaft • Pull the locking bolt out and affix the flexible shaft to the motor until the locking bolt locks in. • Open the air filter cover, screw the accelerator cable in as shown and attach to the throttle valve. •... - Page 18 • Secure the air filter cover with a screw again. • Remove the screw from the handle, insert the other side of the flexible shaft into the handle and use the screw to affix it to the handle. • Use cable ties to affix the accelerator cable to the flexible shaft. b.
- Page 19 c. Assemble the handle • Install the front handle as shown on the image. • Make sure that you align the pin with the hole. Tighten the screws only loosely before you have the most comfortable working position set to the risers. d.
- Page 20 • To demount the blade, use screwdriver to hold flange and pin to release nut, the blade can be taking off. Warning! Please make sure the cutting head has been assembled correctly before use! f. Cutting head for grass trimmer - Align the two holes of the flange and the pin.
- Page 21 • Important! Do not fully tighten the fastening screw until after you have adjusted the chain tension. Tensioning the chain • Important! Always pull out the spark boot plug be- fore performing any checks or adjustments. • Undo the fastening screw (I) of the chain wheel cover by a few turns. •...
-
Page 22: Filling Oil Tank And Fuel Tank
4. FILLING OIL TANK AND FUEL TANK Each time before use, check the following: That there are no leaks in the fuel system. That the equipment is in perfect condition and that the safety devices and cutting devices are complete. That all screws are securely fastened. -
Page 23: Operation
d) Draining fuel Only ever empty the tank outdoors or in well- ventilated rooms. Make sure not to spill fuel or chain oil into the soil (environmental protection). Use a proper base. • Hold a collection container beneath the fuel drain bolt. - Page 24 7) If meet any problems, press the engine switch to off position, the machine will stop running. If need stop cutting head working, release the throttle lever (11). 8) In an emergency, the safety button can be pressed from the harness. The machine then detaches immediately from the carrying strap and falls to the ground.
- Page 25 knives of the hedge trimmer. • Attention! The blades are still running! Do not stop the blades with your hand. Angle adjustment • By swivelling the cutter head, the hedge trimmer can be adjusted to the working conditions. • Warning! Adjust the angle only when the motor has been turned off. •...
- Page 26 Always observe the condition of the tree • Look for rot in the roots and branches. If they are rotten inside, they can break off and fall down unexpectedly during cutting. • You could also attend by fractured and dead branches out. For very thick or heavy branches you first make a small incision below the branch before you work from the top down to avoid chipping.
-
Page 27: Maintenance
6. MAINTENANCE WARNING: Always wear protective gloves when working on or around cutting tools. • For non-use, transport or storage always attach the transport guard to all cutting tools. • Before performing any maintenance or cleaning work, always turn off the engine and pull out the spark boot plug. - Page 28 Grinding the safety hood blade • The safety hood blade can become blunt over time. • When you notice this, undo the screw holding the safety hood blade on the safety hood. • Clamp the blade in a vice. • Sharpen the blade with a flat file and make sure that the angle of the cutting edge is not altered in the process.
- Page 29 Warning! Never run the engine without the air filter element installed. Care of the guide rail Turn the rail around every time you have the chain sharpened or replaced. This will avoid a one-sided wear of the rail, especially at the top and bottom. Regularly clean the opening for the oil supply the oil passage...
- Page 30 B = the angle of the side plate The angle must also be maintained for all knives. For irregular angles, the chain is run irregularly, wear quickly and break down prematurely. Since these requirements can only be met with sufficient and regular exercise: •...
-
Page 31: Storage
7. STORAGE a) Cleaning • Keep handles free of oil, so you always have a secure hold. • Clean the equipment as required with a damp cloth and, if necessary, mild washing up liquid. Important! • Always pull out the spark boot plug each time be- fore carrying out any cleaning. •... -
Page 32: Troubleshooting
9. TROUBLESHOOTING The table below contains a list of fault symptoms and explains what you can do to remedy the problem if your equipment fails to work properly. If the problem persists after working through the list, please contact your nearest ser- vice workshop. Fault Possible cause Remedy... -
Page 33: Declaration Of Conformity
ZI, 32, rue Aristide Bergè s – 31270 Cugnaux - France Tel: +33 (0)5.34.502.502 Fax: +33 (0)5.34.502.503 Declares that the machine: PETROL MULTI TOOL KIT HCOMBIBP50-A Serial No: 20220401151-20220401510 Have been designed in compliance with the following standards: EN ISO 11680-1 :2011 ; EN ISO 11680-2 :2011 ; EN ISO 11806-1 :2011 ; EN ISO 11806-2 :2011 EN ISO 10517-1:2019;... -
Page 34: Warranty
11. WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 35: Product Failure
12. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: • Empty the fuel tank. • Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 36: Warranty Exclusions
13. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...