Advertisement
This unique product is ideal in assisting an exercise routine. The pedometer counts number of steps taken from one location to another. By inputting the stride-length the total distance covered can be calculated.
In this box, you will find:
Keep this manual handy as you use your new product. It contains practical step-by-step instructions as well as technical specifications and warnings you should know about.
Before using the device, pull out the insulation tape underneath the battery cover protecting the 1 x LR43 size 1.5V battery.
NOTE
The unit will not work until the tape is pulled out.
This product uses 1 x LR43 size 1.5V battery. Should you need to change the batteries,
NOTE
Protect the environment by taking exhausted batteries to authorized disposal stations.
Insert a blunt stylus into the HR / + or MIN / - buttons to alter the clock hour and minute values, respectively. The clock is set at 00:00 by default.
NOTE
The unit automatically returns to clock display after 5 seconds if no buttons are pressed.
The distance traveled is shown on the bottom line of the LCD display. For greater accuracy it is recommended that a personal stride-length is set.
Attach securely at waist level to your belt, slacks, or training attire and maintain a horizontal position for more accurate results.
The pedometer counts the number of steps taken.
NOTE
To make the unit more or less sensitive to motion, reposition the motion sensitivity slide switch. To determine the proper amount of motion sensitivity, experiment with different settings. See section on ADJUSTING MOTION SENSITIVITY for more information.
NOTE
Improper positioning of the pedometer may result in incorrect data collection.
Correctly measuring distance depends on accurately setting the average length of an individual stride (stride length) and properly setting an internal motion-sensitivity device.
To return the distance counter to zero, press RESET in DISTANCE display mode.
Total Distance = steps taken x average step length
NOTE
Individual stride-length varies. Input an appropriate length for an average stride. To determine length of stride walk 10 paces and divide distance traveled by 10.
Follow these important procedures below to adjust Pedometer -/+ Motion Sensitivity Switch and ensure accurate readings:
The following conditions may cause incorrect reading of steps taken:
To ensure you use your product correctly and safely, read these warnings and the entire user manual before using the product:
NOTE
The technical specifications for this product and the contents of the user manual are subject to change without notice.
NOTE
Features and accessories will not be available in all countries. For more information, please contact your local retailer.
Step counter | 0 to 99,999 steps |
Distance traveled | 0 to 999.99 km 0 to 999.99 miles) |
Stride distance | 30 to 150 cm (11 to 60 inches) |
Clock | 24 hr |
Dimensions | 65 x 40 x 14 mm (L x W x H) 2.6 x 1.6 x 0.6 inches (L x W x H) |
Weight | 24grams (0.85 ounces) |
Operating Temp | -5.0 to 40.0°C (23 to 104.0°F) |
Storage Temp | -20 to 60°C (-4 to 140°F) |
Batteries | 1 x LR43 1.5 V |
Battery Life | 1 year |
Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products. If you're in the US and would like to contact our Customer Care department directly, please visit: www2.oregonscientific.com/service/support.asp
For international inquiries, please visit: www2.oregonscientific.com/about/international.asp
Hereby, Oregon Scientific, declares that this Digital Pedometer with Real-Time Clock (Model: PE320) is in compliance with EMC directive 2004/108/EC. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Oregon Scientific PE320 - Digital Pedometer User Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the PE320 that isn't answered in the manual? Leave your question here.