Epson SC-P600 Service Manual page 25

Color inkjet printer

Hide thumbs Also See for SC-P600:

User manual (125 pages)

Start here (2 pages)

Start here (2 pages)

Table Of Contents

Table of Contents

SC-P600

Reassemble the Front Tray Assy with the Front Tray raised.

The Front Tray is raised if

Front Tray Assy

the gear is in this position.

Front Tray

The location where frame

Left: Step 4, 5

may interfere.

Front Left Tray Guide

When disassembling/reassembling the Front Tray Assy, there are some locations where the frame and the Front Paper Guide Assy may interfere.

Therefore, be careful not to deform the frame when working.

When removing the Front Tray Assy, follow the procedure below.

1. Remove the screw that secure the Mist Board Assy.

2. Remove the Torsion Spring, 187.9 on the right side of the Front Tray Assy.

3. Remove the E-ring, 3, and remove the Spur Gear, 14.4 and Parallel Pin, 1.5.

4. Remove the screws (x3) that secure the Front Tray Assy.

5. Release the hook and dowel of the Front Left Tray Guide from the frame and slide it to the front of the printer, and then lift the left side of the

Front Tray Assy.

6. Release the hook and dowels (x2) of the Front Right Tray Guide from the frame and slide it to the front of the printer while avoiding the Front Paper

Guide Assy, and then remove the Front Tray Assy by pulling out the Front Tray Shaft and Front Right Tray Guide from the hole of the frame.

 Reassemble the Front Tray Assy with the Front Tray raised. After reassembly, make sure the Front Tray Assy is secured with the hooks and

dowels, and then secure it with the screws.

 After reassembling the Front Tray Assy, confirm the Torsion Spring, 187.9 is correctly attached.

 Before reassembling the Tray Support Assy/Front Tray, confirm the Washer,3.1X0.5X5.4 (x2) and Washer,26X0.5X4.7 (x2) are correctly

attached.

Disassembly/Reassembly

Front Tray Assy

The location where Front Paper

Guide Assy may interfere.

Step 5

Right: Step 2-4

The location where

Front Tray Shaft

Spur Gear, 14.4

frame may interfere.

E-ring, 3

Parallel Pin, 1.5

Front Right Tray Guide

Torsion Spring, 187.9

C.B.P-TITE SCREW,3X6,F/ZN-3C (4 ± 0.5 kgf·cm)

Detailed Disassembly/Reassembly Procedure for each Part/Unit

Attach Cover spring/

Compression spring

to shaft (longer side).

Front Right Tray Guide

Shaft

(shorter

side)

Compression

Spring

Link

Lever

Cover Spring

This side is facing

to frame.

Step 6

When removing the Stopper Tray Unit, follow the procedure below.

1. Remove the Torsion Spring, 187.9.

2. Remove the screws (x2) that secure the Stopper Tray Front Assy and remove the Stopper Tray Front Assy.

3. Remove the Lever Link with Cover Spring and Compression Spring.

4. Remove the E-ring, 3 and Washer, 4.3X0.8X8, and remove the Stopper Tray.

 When attaching the Cover Spring to the Link Lever, attach it as shown above.

 After reassembling the Stopper Tray Unit, confirm the Torsion Spring, 187.9 is correctly attached.

Washer,

3.1X0.5X5.4

26X0.5X4.7

Dowel

Hook

EJ Link Right

Front Right Tray Guide

 When reassembling the Front Tray Assy, install each part as shown above, and secure them with their dedicated washer, parallel pin, and extension spring.

 Before reassembling the Tray Support Assy/Front Tray, confirm the Washer,3.1X0.5X5.4 (x2) and Washer,26X0.5X4.7 (x2) are correctly attached.

Stopper Tray Unit

Align shaft (shorter side)

of Link Lever to cam

groove of Stopper Tray.

Cam groove

Stopper Tray Front Assy

Tray Support Assy / Front Tray

Gear section of Front Tray

Washer,

3.1X0.5X5.4

Spur Gear, 14.4