Terex Genie GS-1432m Operator's Manual
Hide thumbs
Also See for Genie GS-1432m:
- Service and repair manual (261 pages) ,
- Maintenance manual (99 pages) ,
- Operator's manual (69 pages)
Related Manuals for Terex Genie GS-1432m
Summary of Contents for Terex Genie GS-1432m
- Page 1 Operator's Manual Serial Number Range -1432m ™ from GS32mD-101 ANSI/CSA Hong Kong -1932m ™ -1932m Lite ™ with Maintenance Information Original Instructions First Edition First Printing Part No. 1308591GT...
-
Page 2: Table Of Contents
Specifications ............64 Copyright © 2020 Terex Corporation First Edition: First Printing, February 2021 Genie is a registered trademark of Terex South Dakota, Inc. in the U.S.A. and many other countries. “GS” is a trademark of Terex South Dakota, Inc. -
Page 3: Introduction
First Edition • First Printing Operator's Manual Introduction Introduction About this manual Intended Use and Familiarization Guide Genie appreciates your choice of our machine for your application. Our number one priority is user The intended use of this machine is to lift safety, which is best achieved by our joint efforts. - Page 4 First Edition • First Printing Operator's Manual Introduction Platform controls symbology and related Ground controls symbology and related machine movement: machine movement: Lift function enable button Lift function enable button Drive function enable button Platform up/down button Platform up/down (when lift function selected) Sequential functions and movement: Drive forward/reverse (when drive...
- Page 5 First Edition • First Printing Operator's Manual Introduction Bulletin Distribution and Compliance Contacting the Manufacturer Safety of product users is of paramount At times it may be necessary to contact Genie. importance to Genie. Various bulletins are used by When you do, be ready to supply the model Genie to communicate important safety and number and serial number of your machine, along product information to dealers and machine...
- Page 6 First Edition • First Printing Operator's Manual Introduction Safety Sign Maintenance Replace any missing or damaged safety signs. Keep operator safety in mind at all times. Use mild soap and water to clean safety signs. Do not use solvent-based cleaners because they may damage the safety sign material.
-
Page 7: Symbol And Hazard Pictorials Definitions
First Edition • First Printing Operator's Manual Symbol and Hazard Pictorials Definitions Symbol and Hazard Pictorials Definitions Read the operator’s Read the service Crush hazard Crush hazard Collision hazard manual manual Tip-over hazard Tip-over hazard Tip-over hazard Tip-over hazard Electrocution hazard Electrocution hazard Explosion hazard Fire hazard... - Page 8 First Edition • First Printing Operator's Manual Symbol and Hazard Pictorials Definitions Engage safety arm Keep away from Keep clear of tires Move machine to Close chassis tray moving parts level ground Lower the platform. Platform overloaded Maintain required Access by trained Use a piece of clearance and authorized...
- Page 9 First Edition • First Printing Operator's Manual Symbol and Hazard Pictorials Definitions Wheel load Lifting & tie down Lifting point Lanyard anchorage Wind speed instructions points Tiedown Release brakes Engage brake Pressure rating for Voltage rating for air line to platform power to platform Maximum capacity Indoor...
-
Page 10: General Safety
First Edition • First Printing Operator's Manual General Safety General Safety ™ -1432m • GS ™ -1932m • GS ™ -1932m Lite Part No. 1308591GT... - Page 11 First Edition • First Printing Operator's Manual General Safety ™ -1432m • GS ™ -1932m • GS ™ Part No. 1308591GT -1932m Lite...
- Page 12 First Edition • First Printing Operator's Manual General Safety ™ -1432m • GS ™ -1932m • GS ™ -1932m Lite Part No. 1308591GT...
- Page 13 First Edition • First Printing Operator's Manual General Safety ™ -1432m • GS ™ -1932m • GS ™ Part No. 1308591GT -1932m Lite...
- Page 14 First Edition • First Printing Operator's Manual General Safety ™ -1432m • GS ™ -1932m • GS ™ -1932m Lite Part No. 1308591GT...
- Page 15 First Edition • First Printing Operator's Manual General Safety ™ -1432m • GS ™ -1932m • GS ™ Part No. 1308591GT -1932m Lite...
-
Page 16: Personal Safety
First Edition • First Printing Operator's Manual Personal Safety Personal Safety Personal Fall Protection Personal fall protection equipment (PFPE) is not required when operating this machine. If PFPE is required by job site or employer rules, the following shall apply: All PFPE must comply with applicable governmental regulations and must be inspected and used in accordance with the manufacturer’s... -
Page 17: Work Area Safety
First Edition • First Printing Operator's Manual Work Area Safety Work Area Safety Tip-over Hazards Electrocution Hazards Occupants, equipment and materials shall not This machine is not electrically insulated and will exceed the maximum platform capacity or the not provide protection from contact with or maximum platform capacity of the platform proximity to electrical current. - Page 18 First Edition • First Printing Operator's Manual Work Area Safety Do not raise the platform Do not operate the unless the machine is on a machine in strong or gusty firm, level surface. winds. Do not increase the surface area of the platform or the load.
- Page 19 First Edition • First Printing Operator's Manual Work Area Safety Do not operate the machine with the chassis trays Do not modify or alter a mobile elevated work open. platform without prior written permission from the manufacturer. Mounting attachments for holding Do not push off or pull tools or other materials onto the platform, toward any object outside...
-
Page 20: Operating Instructions
First Edition • First Printing Operator's Manual Work Area Safety Crushing Hazard Fall Hazards Keep hands and limbs out of scissors. The guard rail system provides fall protection. If occupant(s) of the platform are required to wear Keep hands clear when folding rails. personal fall protection equipment (PFPE) due to job site or employer rules, PFPE and its use shall Do not work under the platform or in the scissor...