Table of Contents
Advertisement
[
] (Charge) indicator
2
Lights yellow while the battery is being charged.
The indicator will flash rapidly if battery abnormality
occurs.
On the other hand, the indicator will flash slowly if the
battery charge is getting low or the battery temperature
is outside the operating temperature range.
[METER] indicators, [BATTERY CHECK]
3
switch
The [METER] indicators indicate the speaker output.
They also indicate the amount of remaining battery
charge if you press and hold down the [BATTERY CHECK]
switch. How to read the amount of remaining charge
(See page 15.)
4
MONITOR/LINK [LEVEL] control
Determines the signal level output from the OUTPUT
[MONITOR/LINK] jack.
If multiple units of this product are connected, you can
set this control to the LINK position to easily balance the
volume level between multiple units.
5
MAIN [FEEDBACK SUPPRESSOR] switch and
indicator
Press this switch to apply the feedback suppressor. The
indicator lights yellow.
6
MAIN [LEVEL] control
Adjusts the speaker volume.
7
MAIN [LIMIT] indicator
Lights up if the speaker volume becomes excessive,
causing the limiter to activate.
NOTE
If this indicator lights up frequently, turn the MAIN [LEVEL]
control to lower the speaker volume.
8
MAIN [MODE] control
Use this control to adjust the overall sound pressure and
frequency balance. The center position (MUSIC) is a basic
setting.
• If you turn the control counterclockwise (toward
SPEECH), it will cut unneeded low-range frequencies,
and create an optimum setting for speech, or singing
and playing an acoustic musical instrument.
• If you turn the control clockwise (toward CLUB), it will
boost the high and low ranges, and create an optimum
setting for playback of sound sources.
MAIN [REVERB TYPE/TIME] control
9
Determines reverb type and length. Each " " mark
labeled around the control refers to the length of
corresponding reverb.
• HALL: Simulated reverb of a large space, such as a
concert hall.
• PLATE: Simulated steel plate reverb, producing a
harder-edged and brighter sound.
• ROOM: Simulated acoustic ambiance of a small room.
• ECHO: Echo effect suitable for karaoke.
10
STAGEPAS 200BTR STAGEPAS 200 Owner's Manual
[MIC, LINE/LINK] switch (channel 1),
)
[MIC, LINE] switches (channels 2 & 3)
For low-level signals (including microphones), set the
switches to the MIC (N) position. For high-level signals
(including electronic musical instruments and audio
devices), set the switches to the LINE/LINK or LINE (O)
position.
[Hi-Z] switches (channels 2 & 3)
!
You can use these switches when connecting a musical
instrument with passive pickups (without a battery), such
as an acoustic-electric guitar or electric bass. Turn on the
switches when you connect these instruments directly to
the mixer without using a DI (direct box).
This function is effective only for the signals input via the
phone jacks.
@
[
] (Bluetooth) switch and indicator
(channel 4/5)
This switch turns the Bluetooth audio connection on or
off. It is used to pair (register) a Bluetooth device
(page 20). The indicator shows the following status:
[
] (Bluetooth)
Status
indicator
Off
Bluetooth standby mode
Lit steadily
Bluetooth connected
Flashing slowly
Searching for a Bluetooth device
Flashing rapidly
Waiting for Bluetooth pairing
Flashing twice
Authorizing STAGEPAS Controller
NOTE
This product enables you to pair (register) up to eight Bluetooth
devices. Once the ninth Bluetooth device has been paired
successfully, the pairing information for the Bluetooth device
that was connected earliest will be deleted.
[LEVEL] controls (channels 1–3, channel 4/5)
#
Use these controls to adjust the volume for the
corresponding channels. To reduce noise, set the [LEVEL]
controls on unused channels to minimum (zero).
Channel 1 [LEVEL] control is also useful when you adjust
the input level in the LINK connection. If multiple units of
this product are connected, you can use this control,
along with the MONITOR/LINK [LEVEL] control (
set it to the LINK position to easily balance the volume
level between multiple units.
[PEAK] indicators (channels 1–3)
$
Light red if signals are almost clipping due to excessive
input levels. If these indicators light up, lower the level of
the corresponding input channel signals, or set the
corresponding [MIC, LINE/LINK] switches or [MIC, LINE]
switch to the LINE/ LINK or LINE position.
4
), and
Advertisement
Table of Contents
