Related Manuals for Ariens 18 Series
Summary of Contents for Ariens 18 Series
- Page 1 9 9 0 0 1 1 ® Series,18” Rear Tine Rotary Tiller Owner's Manual PRINTED IN USA PART NO. 001525B 11-95...
-
Page 2: Safety Alert Symbol And Notations
A Message to Ariens Customers. . . Welcome to the world of Ariens equipment. We are engine repairs or services are required, they can be pleased that you have purchased the best equipment obtained from an Ariens dealer or from an authorized available. -
Page 3: Table Of Contents
NEVER attempt to make any adjustment to unit while engine is running (except where specifically Keep the area of operation clear of all persons recommended). particularly children and pets. © 1995 Ariens Company - All Rights Reserved... - Page 4 Disengage Main Clutch, stop engine, wait for moving Use only attachments and accessories approved by parts to stop and remove wire to spark plug before Ariens Company. Use Ariens attachments only when attempting to unclog tines or make any repairs, recommended.
-
Page 5: Safety Decals
Safety Decals WARNING C A U T I O N When Starting Engine Make Sure Main Clutch Is Do not operate tines In Neutral and Axle Drive Pins Are Engaged in Wheel with wheel hub drive Hubs Place Feet Firmly On The pins disengaged. -
Page 6: Controls And Features
Controls and Features Wheel Hub Drive Pins 901021 & 901023 901421 & 901423 Disengaged Engaged 901022 & 901422 1. Wheel Hub Drive Pins (Each Side) 2. Gas Fill 3. Engine Controls 4. Recoil Starter 5. Main Clutch Rod 6. Handlebar 7. -
Page 7: Operation
Operation Pre-Starting In order to become familiar with the tiller, when first operating it, use lowest engine speed that will still give sufficient power to operate. After you become Check that engine crankcase oil is full using dipstick. familiar with tiller increase throttle to "FAST" position See Page 9 to add or change. - Page 8 Operation (Continued) NOTE: When Main Clutch is in "NEUTRAL" forward and reverse idlers are disengaged. To engage Main Clutch, push Main Clutch Rod forward (Forward drive will continue when Main Clutch Rod is pushed all the way forward). In order to return Main Clutch to "NEUTRAL", pull and release Main Clutch Rod.
- Page 9 Operation (Continued) Stopping Tiller NOTE: Tilling depth will vary with ground conditions. Depth stick increases drag when point is installed forward. To stop tiller, position Main Clutch in "NEUTRAL" and move throttle control to stop. When reaching end of a row. lift handlebars to raise tines out of ground.
-
Page 10: Lubrication And Maintenance
Ariens dealers will provide any service which may be Drain crankcase by removing oil drain plug. When oil required to keep tractor operating at peak efficiency. - Page 11 Every twenty five hours or at start of tilling operation check oil level in the gear boxes. If necessary, add Ariens L-2 Special Gear Lubricant at oil fill port, figure IMPORTANT: Serious damage can be caused to 5, check and replace plug when full.
- Page 12 Check Engine Cooling System Check the Air Cleaner Lubricate all Pivot Points Check the Fasteners Adjust the Fwd-Rev Clutch Check the Transmission Oil Check the Tire Pressure Chart 1 Always use genuine Ariens service parts and accessories to ensure your machines peak performance.
- Page 13 Lubrication and Maintenance (Continued) 25 HRS. ACTUAL HOURS DATE 50 HRS. ACTUAL HOURS DATE 75 HRS. ACTUAL HOURS DATE 100 HRS. ACTUAL HOURS DATE 125 HRS. ACTUAL HOURS DATE 150 HRS. ACTUAL HOURS DATE 175 HRS. ACTUAL HOURS DATE 200 HRS. ACTUAL HOURS DATE 225 HRS.
- Page 14 Lubrication and Maintenance (Continued) 375 HRS. ACTUAL HOURS DATE 400 HRS. ACTUAL HOURS DATE 425 HRS. ACTUAL HOURS DATE 450 HRS. ACTUAL HOURS DATE 475 HRS. ACTUAL HOURS DATE 500 HRS. ACTUAL HOURS DATE 525 HRS. ACTUAL HOURS DATE 550 HRS. ACTUAL HOURS DATE 575 HRS.
-
Page 15: Adjustments
Adjustments Belt Speed Drive Belt Tension To change speeds, drive belts is shifted from one Before checking tension - Engine must be turned off sheave groove to the other groove. (Refer to and spark plug wire must be removed from plug. instruction decal on belt guard.) After the belts have seated in from use, check the tension adjustment on the forward belt. -
Page 16: Storage
Components commonly used for consumer service, can be ordered through your Ariens Dealer. When Rear Tine Rotary Tiller ordering parts always include the Model and Serial Service Manual Number of your unit to assure prompt service. -
Page 17: Trouble Shooting
Trouble Shooting Engine recoil operates but engine will not The tractor will not move when the start. direction control lever is moved to “Forward” or “Reverse” position. Fuel tank empty. Fuel shut-off valve at the fuel tank turned off Fwd-Rev clutch needs adjustment Engine failure - See Engine Manual Attachment jammed or damaged Engine starts but runs roughly. -
Page 18: Specifications
Specifications Model No. 901021 901022/901422 901023/901423 Descriptive Name RT5018 RT4018 RT6018 Length 58” 58” 58” Height 42” 42” 42” Width 24” 24” 24” Weight 165 Lbs. 160 Lbs. 165 Lbs. Engine - Manufacture B & S Tecumseh Tecumseh - No. Cycles Four Four Four... -
Page 19: Dealer Preparation
Dealer Preparation Customer Note: Yours Ariens Dealer is expected to complete these preparation steps and review important information, including this manual, with you before or upon delivery of machine or attachment. Handlebar Assembly The preparation information is included here so that you and your dealer may review it together. - Page 20 Explain Ariens Company, Limited Warranty Policy, fill out Original Purchaser Registration Card, Parts and Repair Manuals Order Form and return to Ariens Check oil level of gear case before starting unit, refer Company. Place Model and Serial Number on page to Lubrication and Maintenance Section, starting on (1) of this manual.
-
Page 21: Warranty
Ariens Company hereby warrants to the original consumer purchaser that WARRANTY WARRANTY products manufactured by Ariens Company will be free from defects in material and workmanship FOR A PERIOD OF FIVE (5) YEARS FROM THE DATE OF PURCHASE, EXCEPT AS NOTED BELOW. - Page 22 Index Adjustments Safety Alert Symbol and Notations Belt Finger Belt Speed Safety Decals Belt Tension Handlebar Safety Precautions Tilling Width Maintenance and Storage Operation Controls and Features Preparation Training Dealer Preparation Package Contents Service Manual Steps to Assemble Tools Required Specifications Lubrication &...
- Page 23 Ask your dealer for information about these other fine Ariens Products: • Front and Rear Tine Tillers • 21" Walk-Behind Lawn Mowers • Walk-Behind Sno-Thros • Rear Engine Riding Mowers • Yard and Garden Tractors • Commercial Walk-Behind and Riding Mowers Ariens Company 655 W.