NAD 160 Owner's Manual page 5

13. VOLUME PRE OUT 2
The VOLUME Pre Out 2 control allows for adjustment of the output
level of the PRE OUT 2 sockets. The output level can be reduced
by up to 12dB; when set to the maximum position (at the 0dB
position), the output level will be identical to that of the PRE OUT
1 sockets. Refer also to chapter "Bi-amping" for more
information.
NOTE: always turn the pre-amplifier and associated power
amplifiers off before connecting or disconnecting anything to the
Pre-Out 1 & 2 sockets.
14. NAD LINK IN, OUT
The NAD-Link connector is used to pass commands from other
units fitted with NAD-Link connectors. This allows centralised
control of a complete system, and also allows some of the basic
functions of other NAD components (such as a CD player or
cassette-deck) also equipped with NAD-Link to be controlled with
the pre-amplifier's remote control. To function with such other
units, connect the C160's NAD-Link Out to the NAD-Link In on the
other unit. NAD-Link connectors can be daisy-chained, IN to OUT,
so that a whole system can be controlled from the remote control
facilities of one unit.
15. 12V TRIGGER OUT
The 12V trigger is activated automatically when switching the NAD
C160 from off or stand-by to on. Connect the 12V trigger to a
power amplifier or AC outlet power strip equipped with a 12V
trigger input for remote on/off switching of those devices. Use a
cable terminated with a 3.5mm Mini-Jack connector at the pre-
amplifier's end for connection.
16. AC LINE CORD
Plug the AC power cord into a live AC wall socket. Make sure all
connections have been made before connecting to mains.
17. SWITCHED AND UNSWITCHED POWER
OUTLETS (AH VERSION ONLY)
The AC power cords of other stereo components, such as a CD
player, may be plugged into these accessory outlets. Components
plugged into the outlet marked "switched" will be switched on
and off as the pre-amplifier is switched from stand-by or off to on
and vice versa.
Mains power is always available on the outlet marked
"unswitched" as long as the NAD C160's power cord is plugged
into a live AC wall outlet. This outlet can be used for components
which may require continuous supply of AC mains; some tuners
require uninterrupted mains supply to retain preset memory, for
instance.
NOTE: The total power consumption of any components
connected to the AC outlets may not exceed 100 Watts. Never
connect the mains lead of a power amplifier to either the Switched
or Unswitched outlets of the NAD C160.
QUICK START
1. Connect a twin RCA lead to a power amplifier.
2. Connect the desired sources to the relevant input sockets on the
rear.
3. Connect speakers to the power amplifier.
4. Plug in the AC power cord.
5. Press the POWER button to turn on the NAD C160.
6. Switch on the power amplifier
7. Press the required input selector.
FRONT PANEL CONTROLS
1. POWER ON/OFF
Press the POWER button to switch the pre-amplifier to its 'Stand-
by' mode. The Stand-by indicator (No. 2) over the power button
will light up amber. On the front panel, press any of the input
selector buttons to switch to pre-amplifier on. From the remote
control, press the green Stand-by button (located just over the
Speakers A and B buttons) to switch the unit on. The Stand-by
indicator will turn from amber to green to indicate it is switched
on and ready for use.
REMOTE CONTROL
STAND-BY BUTTON (GREEN)
Press the Power button to switch the unit on, the Stand-by
indicator on the front panel will turn from amber to green within
2 seconds, meanwhile the CD indicator automatically flashes 4
times . The unit is now ready for use
NOTE: In Stand-by mode the C160 uses very little power.
However, it is recommended that you switch the unit totally off if
it is not going to be used for more than a couple of days. Switch
off completely by pressing the POWER button on the front panel
(No. 1), all lights will extinguish.
2. STAND-BY INDICATOR
The indicator LED offers information on the status of the NAD
C160:
Off: The unit is switched off totally.
Amber: The unit is in stand-by mode
Green: The unit is switched on and ready for use.
The LED will also flash when the pre-amplifier receives a remote
control command from the supplied handset.
3. HEADPHONE SOCKET
A 1/4" stereo jack socket is supplied for headphone listening and
will work with conventional headphones of any impedance.
Inserting a headphone jack into this socket automatically switches
off the output to the PRE OUT 1 & 2 sockets on the back panel.
The volume, tone and balance controls are operative for
headphone listening. Use a suitable adapter to connect
headphones with other types of sockets, such as 3.5mm stereo
'personal stereo' jack plugs.
NOTE: Listening at high levels can damage your hearing.
4. INFRA-RED REMOTE CONTROL COMMAND
RECEIVER
The infrared sensor, located behind this circular window, receives
commands from the remote control. There must be a clear line-
of-sight path from the remote control to this window; if that path
is obstructed, the remote control may not work.
GB
5