Installation And Connection; Ac Power Connection; Signal Cable Connection; Connecting To Any Ibm Vga Compatible System - Mitsubishi Diamond Plus 120U User Manual

3
3
INSTALLATION AND
CONNECTION
On the back of the monitor four kinds of plug-in connections
are provided: AC power connector for the AC input, DB9-
15P connector and BNC connector for video signal input
and USB ports for USB communication.
3.1

AC Power Connection

One end of the AC power cord is connected into the AC
power connector on the back of the monitor. The other end
is plugged into a properly grounded three-prong AC outlet.
The monitor's auto-sensing power supply can automati-
cally detect 100-120V AC or 220-240V AC and 50 or 60Hz.
3.2

Signal Cable Connection

The attached video signal cable provides a DB9-15P
connector for the VGA compatible analog RGB outputs on
your computer. Apple Macintosh Computers can also be
interfaced with using the included Mitsubishi Macintosh
adapter AD-A205.
3.2.1 Connecting to Any IBM VGA Compatible Sys-
tem
Figure 5 shows the SC-B102 or SC-B104 cable connection
to the Video Graphics Array (VGA) port in an IBM Personal
®
System/2 series, or any VGA compatible system.
1. Power off, both the monitor and the computer.
2. Connect the one end of the SC-B102 or SC-B104
cable to the DB9-15P connector on the VGA control-
ler card.
3. Connect the other end of the SC-B102 or SC-B104
cable to the DB9-15P receptacle on the back of the
monitor.
4. Power on the computer, then the monitor.
5. After using the system, power off the monitor, then off
the computer.
D-SUB
BNC
COMP.
A B 1 R G B HD VD
2
D-SUB
BNC
COMP.
R G B HD
Power Cord Cable SC-B102 or SC-B104
Figure 5.
CAUTION
The socket-outlet shall be installed near the equipment
and shall be easily accessible. During servicing, discon-
nect the plug from the socket-outlet.
Méme si le moniteur est mis hors tension il reste toujours
alimenté. La prise secteur devrait ainsi ètre facilement
accssible en cas d'urgence.
Computer
VGA
Compatible
System
VD
DB9-15P

3.2.2 Connecting to An Apple Macintosh Computer

Figure 6 shows the SC-B102 or SC-B104 cable and AD-
A205 Adapter to the video port in an Apple Macintosh.
1. Power off, both the monitor and the computer.
2. Set the DIP switches of Macintosh Adapter according
to the setting chart.
(See 7.3 Macintosh Adapter AD-A205 settings)
3. Connect the 15-pin (DB-15P) end of the AD-A205
Adapter to the straight 15-pin connector on the
Macintosh video port on the computer or on the video
board.
4. Connect the sub-miniature 15-pin (DB9-15P) end of
AD-A205 Adapter to the SC-B102 or SC-B104 cable.
5. Connect the other end of the SC-B102 or SC-B104
cable to the DB9-15P receptacle on the back of the
monitor.
6. Power on the Macintosh, then the monitor.
7. After using the system, power off the monitor, then off
the Macintosh.
D-SUB
BNC
R G B
A B 1
2
D-SUB
R
Power Cord
3.2.3 Connecting to a Unix Workstation & Third Party
Graphics Card
Figure 7 shows the SC-B102 (or SC-B104) or "75 " coaxial
cable (not supplied) connection to the graphics video card
(PC-CAD and workstation).
1. Power off, both the monitor and the computer.
2. Connect one end of the SC-B102 (or SC-B104) cable
or the "75 " coaxial cable to the output connector on
the computer, or on the video board.
3. Connect the other end of the SC-B102 (or SC-B104)
cable or the "75 " coaxial cable to the DB9-15P
receptacle or the BNC receptacles on the back of the
monitor.
4. Power on the computer, then the monitor.
5. After using the system, power off the monitor, then off
the computer.
D-SUB
BNC
R G B
A B 1
2
D-SUB
R
Power Cord
Please see next page about BNC connection.
- 10 -
Computer
COMP.
HD
VD
Apple Macintosh
Computer
BNC Macintosh
COMP.
G B HD
VD
Adapter
AD-A205
Cable SC-B102 or SC-B104
Figure 6.
High Resolution
COMP.
HD
VD
Graphic Video Card
BNC
COMP.
G B
HD
VD
High Resolution
Graphic Video Card
"75 " coaxial cable
Cable SC-B102 or SC-B104
Figure 7.