Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for MSI 661FM3-L
Summary of Contents for MSI 661FM3-L
- Page 1 661FM3 Series MS-7082 (V1.X) Mainboard G52-70821X1...
-
Page 2: Copyright Notice
If a problem arises with your system and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance. Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates, and other information: faq/esc_faq_list.php Contact our technical staff at: http://support.msi.com.tw/... -
Page 3: Safety Instructions
Safety Instructions Always read the safety instructions carefully. Keep this User’s Manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protects the equip- ment from overheating. -
Page 4: Fcc-B Radio Frequency Interference Statement
FCC-B Radio Frequency Interference Statement T h is eq uip men t h as been tested and found to c omply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 5: Weee (Waste Electrical And Electronic Equipment) Statement
WEEE (Waste Electrical and Electronic Equipment) Statement... -
Page 8: Table Of Contents
Copyright Notice ... ii Trademarks ... ii Revision History ... ii Technical Support ... ii Safety Instructions ... iii FCC-B Radio Frequency Interference Statement ... iv W EEE (Waste Electrical and Electronic Equipment) Statement ... v Chapter1 Getting Started ... 1-1 Mainboard Specifications ... - Page 9 BIOS Flash Jumper: BIOS_WP1 ... 2-16 Slots ... 2-17 AGP (Accelerated Graphics Port) Slot ... 2-17 PCI (Peripheral Component Interconnect) Slots ... 2-17 PCI Interrupt Request Routing ... 2-17...
-
Page 10: Chapter1 Getting Started
Chapter 1 Getting Started Thank you for purchasing 661FM3 Series (MS-7082 v1.X) Micro ATX mainboard. The 661FM3 Series (MS- 7082 v1.X) is based on SiS for optimal system efficiency. Designed to fit the ad- ® vanc ed Intel Pentium 4/Celeron D processor, the 661FM3 Series (MS-7082 v1.X) deliv- ers a high performance and professional desktop plat- form solution. -
Page 11: Mainboard Specifications
M S-7082 M ainboard Mainboard Specifications Processor Support ® - Intel Pentium 4/ Celeron-D in the LGA 775 package. (For the latest information about CPU, please visit http://www.msi. com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support. php) Supported FSB - 533/ 800 MHz Chipset ® - North Bridge: SiS 661FX chipset ®... - Page 12 Getting Started Connectors Back panel - 1 PS/2 mouse port - 1 PS/2 keyboard port. - 1 Serial port - 1 Parallel port supporting SPP/EPP/ECP mode - 1 VGA port - 4 USB 2.0 Ports. - 1 LAN jack (10/100) by Realtek 8100C - 1 (3 in 1) audio connector On-Board Pinheaders - 1 IrDA pinheader...
-
Page 13: Mainboard Layout
M S-7082 M ainboard Mainboard Layout T: mouse B: keyboard JPW2000 BIOS_WP1 Line-In Line-Out B:Mic Winbond W83627THG AGP Slot RTL8100C PCI Slot 1 PCI Slot 2 PCI Slot 3 ALC655 JSP1 CD_IN1 JAUD1 (MS-7082 v1.X) Mainboard CPUFAN1 661FX COM1 661FM3 Series CHSFAN1 JFP1 SATA2... -
Page 14: Chapter2 Hardware Setup
Hardware Setup Chapter 2 Hardware Setup This chapter provides you with the information about hardware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly. -
Page 15: Quick Components Guide
M S-7082 M ainboard Quick Components Guide JPW2000, p.2-8 Back Panel I/O, p.2-9 BIOS_WP1, p.2-16 IR1, p.2-13 PCI Slots, p.2-17 CD_IN1, p.2-15 JSP1, p.2-14 CPUFAN1, p.2-12 CPU, p.2-3 AGP Slot, p.2-17 JCOM1, p.2-12 JAUD1, p.2-13 DDR DIMMs, p.2-7 CONN1, p.2-8 FDD1, p.2-10 IDE1, IDE2, p.2-10... -
Page 16: Cpu (Central Processing Unit)
If you do not have the CPU, contact your dealer to purchase and install them before turning on the computer. For the latest information about CPU, please visit http://www.msi.com.tw/program/ products/mainboard/mbd/pro_mbd_cpu_support.php Important 1. -
Page 17: Lga775 Cpu & Cooler Installation
M S-7082 M ainboard LGA775 CPU & Cooler Installation W hen you are installing the CPU, make sure the CPU has a cooler attached on the top to prevent overheating. If you do not have the cooler, contact your dealer to purchase and install them before turning on the computer. - Page 18 5. Lift the load lever up and open the load plate. 7. Visually ins pect if the CPU is seated well into the socket. If not, take out the CPU with purely verti- cal motion and reload it again. Then c over t he l oad plat e on to t he package.
- Page 19 M S-7082 M ainboard 11. Turn over the mainboard to confirm that th e c li p-en ds are c orrec tly inserted. Important 1. Check the information in BIOS (Chapter 3) for the CPU temperature. 2. Whenever CPU is not installed, always protect your CPU socket pin with the plastic cap covered (shown in Figure 1) to avoid damaging.
-
Page 20: Memory
The mainboard provides two 184-pin unbuffered DDR266/DDR333/DDR400 DDR SDRAM, and supports the memory size up to 2GB without ECC. To operate properly, at least one DIMM module must be installed. For more information on compatible components, please visit http://www.msi.com.tw/ program/products/mainboard/mbd/pro_mbd_trp_list.php 184-pin, 2.5V... -
Page 21: Power Supply
M S-7082 M ainboard Power Supply ATX 20-Pin Power Connector: CONN1 This connector allows you to connect to an ATX power supply. To connect to the ATX power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. -
Page 22: Back Panel
Back Panel Parallel M o us e Keyboard COM Port M ouse/Keyboard Connector ® The standard PS/2 mouse/keyboard DIN connector is for a PS/2 Parallel Port Connector A parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode. -
Page 23: Connectors
M S-7082 M ainboard Connectors Floppy Disk Drive Connector: FDD1 This standard FDD connector supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. ATA133 Hard Disk Connectors: IDE1 & IDE2 The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/ 133 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 66/100/133 function. -
Page 24: Serial Ata Ii Connectors: Sata1 & Sata2
Serial ATA II Connectors: SATA1 & SATA2 SATA1~SATA2 are high-speed SATA interface ports. Each supports data rates of 150 MB/s and is fully compliant with Serial ATA specifications. Each Serial ATA con- nector can connect to 1 hard disk device. SATA2 SATA1 Serial ATA cable... -
Page 25: Fan Power Connectors: Cpufan1 & Chsfan1
M S-7082 M ainboard Fan Power Connectors: CPUFAN1 & CHSFAN1 The fan power connectors support system cooling fan with +12V. W hen connecting the wire to the connectors, always take note that the red wire is the positive and should be connected to the +12V, the black wire is Ground and should be connected to GND. -
Page 26: Front Panel Audio Connector: Jaud1
Front Panel Audio Connector: JAUD1 The JAUD1 front panel audio connector allows you to connect the front panel audio ® and is compliant with Intel Front Panel I/O Connectivity Design Guide. SIGNAL AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC AUD_FPOUT_R AUD_RET_R HP_ON AUD_FPOUT_L AUD_RET_L Important If you don’t want to connect to the front audio header, pins 5 &... -
Page 27: Front Usb Connectors: Jusb1 & Jusb2
M S-7082 M ainboard Front USB Connectors: JUSB1 & JUSB2 The mainboard provides USB 2.0 pinheaders (optional USB 2.0 bracket available) that ® are compliant with Intel I/O Connectivity Design Guide. USB 2.0 technology increases data transfer rate up to a maximum throughput of 480Mbps, which is 40 times faster than USB 1.1, and is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras, M P3 players, printers, modems and the like. -
Page 28: Front Panel Connectors: Jfp1
Front Panel Connectors: JFP1 The mainboard provides one front panel connector JFP1 for electrical connection to the front panel switches and LEDs. It is compliant with Intel tivity Design Guide. SIGNAL HD_LED_P FP PWR/SLP HD_LED_N FP PWR/SLP RST_SW_N PWR_SW_P RST_SW_P PWR_SW_N RSVD_DNU CD-In Connector: CD_IN1... -
Page 29: Button
M S-7082 M ainboard Jumper The motherboard provides the following button for you to set the computer’s function. This section will explain how to change your motherboard’s function through the use of button. Clear CMOS Jumper: JBAT1 There is a CMOS RAM on board that has a power supply from external battery to keep the data of system configuration. -
Page 30: Slots
Slots AGP (Accelerated Graphics Port) Slot The AGP slot allows you to insert the AGP graphics card. AGP is an interface speci- fication designed for the throughput demands of 3D graphics. It introduces a 66MHz, 32-bit channel for the graphics controller to directly access main memory. PCI (Peripheral Component Interconnect) Slots The PCI slots support LAN cards, SCSI cards, USB cards, and other add-on cards that comply with PCI specifications.