Leviton Decora Mural MDE03-1 Installation Instructions

C O L L E C T I O N B Y L E V I T O N • Leviton's Decora
• Soft fade ON/OFF
• Minimum Brightness Adjustment
• Brightness Level Display
Single Pole (One location) or
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This
3-Way (Multi-location)
device must accept any interference received, including interference that may cause undesired operation.
Electronic Low-Voltage
WARNING:
Cat. No. MDEØ3-1
WARNING:
(w/brightness level display)
WARNING:
120VAC, 60Hz
FLUORESCENT LIGHTING, A MOTOR- OR A TRANSFORMER-OPERATED APPLIANCE OTHER THAN APPROPRIATE LOW-VOLTAGE LIGHTING.
350VA
CAUTION:
LEVITON MAGNETIC LOW-VOLTAGE DIMMER TO CONTROL MAGNETIC LOW-VOLTAGE TRANSFORMERS.
Total minimum wattage must
exceed 40W or 40VA CAUTION:
THE DIMMER COOLS DOWN AND RESETS. IF THIS SHOULD OCCUR, THE EXCESS LOAD MUST BE REMOVED TO RESUME PROPER OPERATION.
For use w/Cat. No. MSEØR-1 Multi-Remote™
OTHER CAUTIONS:
1. USE ONLY ONE (1) DIMMER IN A MULTI-LOCATION CIRCUIT. THE SWITCH(ES) WILL TURN THE LIGHT
INSTALLATION INSTRUCTIONS
2. DISCONNECT POWER WHEN SERVICING FIXTURE OR CHANGING LAMPS.
3. USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE. WITH ALUMINUM WIRE USE ONLY
MULTI-GANG INSTALLATION:
DI-000-MDE03-00A
When ganging dimmers, the side sections of the mounting strap must be removed. Use pliers to carefully bend
side sections back and forth until they break off (refer to Figure 1). The side sections dissipate heat, so
removing them requires a derating of the dimmer's capacity (refer to chart).
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
MAXIMUM BULB WATTAGE (For Electronic Low-Voltage Only):
Leviton warrants to the original consumer purchaser and not
for the benefit of anyone else that this product at the time of
Low-voltage dimmers are rated in Volt-Amps (VA). The maximum bulb wattage is
its sale by Leviton is free of defects in materials and
determined by the efficiency of the transformer in the low-voltage lighting system.
workmanship under normal and proper use for two years
Transformer efficiencies will vary from different manufacturers; consider 90% efficient as
from the purchase date. Leviton's only obligation is to correct
such defects by repair or replacement, at its option, if within average. Use the chart to determine maximum bulb wattage for typical transformer
such two year period the product is returned prepaid, with
efficiency ratings.
proof of purchase date, and a description of the problem to
Leviton Manufacturing Co., Inc., Att: Quality Assurance TO INSTALL:
Department, 59-25 Little Neck Parkway, Little Neck, New
York 11362-2591 (In Canada send to Leviton Mfg. of 1.
Canada Ltd., 165 Hymus Blvd., Point Claire, (Quebec),
Canada H9R 1E9). This warranty excludes and there is
disclaimed liability for labor for removal of this product or
2. Remove existing wallplate and switch or dimmer, if applicable.
reinstallation. This warranty is void if this product is installed
improperly or in an improper environment, overloaded, 3. Remove 3/4" (1.9 cm) of insulation from each circuit conductor. Make sure that ends of conductors are
misused, opened, abused, or altered in any manner, or is
not used under normal operating conditions or not in
accordance with any labels or instructions. There are no other
4. Connect lead wires per appropriate WIRING DIAGRAM as follows:
or implied warranties of any kind, including merchantability
and fitness for a particular purpose, but if any implied warranty
is required by the applicable jurisdiction, the duration of any
such implied warranty, including merchantability and fitness
for a particular purpose, is limited to two years. Leviton is not
liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of
use of, any equipment, lost sales or profits or delay or failure
to perform this warranty obligation. The remedies provided
herein are the exclusive remedies under this warranty,
whether based on contract, tort or otherwise.
NOTE: This model incorporates a trim adjustment which will allow the installer to precisely set the low end of
the dimming range to suit each installation. This adjustment is preset at the factory and should require no
For Technical Assistance Call:
further adjustments for most installations. If adjustment is required proceed as follows, otherwise continue with
1-800-824-3005 (U.S.A. Only)
step 7:
1 800 405-5320 (Canada Only)
5. The brightness adjustment is located on the side of the dimmer (refer to Figure 1). Using a small, insulated
www.leviton.com
DI-000-MDE03-00A
DI-000-MDE03-00A 1
® Style design • Double Tap functions
• Power interruption – load returns to existing state
• ON/OFF LED indicates status of load
• Color conversion available
FCC COMPLIANCE STATEMENT
INSTALLATION INSTRUCTIONS
TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN.
TO AVOID OVERHEATING AND POSSIBLE DAMAGE TO THIS DEVICE AND OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE,
USE WITH ELECTRONIC LOW-VOLTAGE TRANSFORMERS ONLY. DO NOT USE TO CONTROL A MAGNETIC LOW-VOLTAGE TRANSFORMER. USE A
THIS DIMMER PROVIDES PROTECTION FROM OVERHEATING. IF MORE THAN THE RATED WATTAGE IS APPLIED, THE LOAD WILL SHUT OFF UNTIL
ON AT THE BRIGHTNESS LEVEL SELECTED AT THE DIMMER. FOR MULTI-LOCATION APPLICATIONS,
USE MSEØR-1 REMOTE(S).
DEVICES MARKED CO/ALR OR CU/AL.
WARNING:
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
straight.
ELECTRONIC LOW-VOLTAGE DIMMER ONLY TO THE PRIMARY (HIGH-VOLTAGE) SIDE OF A
ELECTRONIC LOW-VOLTAGE TRANSFORMER. Twist strands of each lead tightly and, with circuit
conductors, push firmly into appropriate wire connector (see chart for allowable wire connector and
number of conductor combinations). Screw connectors on clockwise making sure that no bare conductor
shows below the wire connectors. Secure each connector with electrical tape.
NOTE: For single pole applications, cap YELLOW lead with an appropriate size wire connector. Secure
connector with electrical tape.
screwdriver, depress and hold the brightness adjustment switch. To increase the minimum brightness, press
the upper half of the rocker. To decrease the minimum brightness, press the lower half of the rocker.
FEATURES
MAXIMUM LOAD PER CONTROL FOR MULTI-GANG
Cat. No. Single
MDEØ3-1L 350VA
MAXIMUM BULB WATTAGE AT 90% EFFICIENCY
Rating
350VA
WIRE CONNECTOR / # OF COND. COMBINATION CHART
1- #12 w/ 1 to 3 #14, #16 or #18 2- #14 w/ 1 #16 w/ 1 or 2 #18 or #20
2- #12 w/ 1 #14 w/ 1 #16 or #18 3- #14 w/ 1 or 2 #18 or #20
2- #12 w/ 1 #16 w/ 1 or 2 #18 4- #14 w/ 1 #16 or #18
2- #14 w/ 1 to 3 #16, #18 or #20 2- #16 w/ 1 #18 w/ 1 or 2 #20 or #22
4- #16 w/ 1 or 2 #18, #20 or #22 1- #14 w/ 1 #18 w/ 1 to 3 #20
1- #14 w/ 1 to 4 #16, #18 or #20 3- #14 w/ 1 #16 w/ 1 #18, #20, #22
2- #14 w/ 1 to 3 #16, #18 or #20 3- #14 w/ 1 #18 w/ 1 #20 or #22
Figure 1 – Dimmer Functions
WARNING:
CONNECT A
Mounting Strap
Side Sections
Upper
Rocker
Brightness Level
Display
Lower
Rocker
Air Gap
Switch
12/27/02, 4:14 PM
Two More than
Gang 2 Gang
250VA 200VA
Two More than
Single Gang 2 Gang
315W 225W 180W
Minimum Brightness
Adjustment Switch
ON/OFF
LED