Advertisement
6. Release the rocker. Release adjustment switch and minimum brightness is set. Check for proper operation
by tapping the lower half of the rocker so the lights turn OFF, then tapping the upper half of the rocker so the
lights turn ON. The lights will turn ON to the new minimum brightness set. If minimum brightness level is not
satisfactory, repeat step 5.
7. Carefully position all wires to provide room in outlet box for dimmer. Mount dimmer into box with mounting
screws supplied.
8. Restore power at circuit breaker or fuse. Turn the dimmer ON by pressing the upper half of the rocker. The
GREEN ON/OFF LED will turn OFF to indicate the dimmer is ON (when the dimmer is OFF, the LED is ON).
9. Attach Decora
®
wallplate (not included). INSTALLATION IS COMPLETE.
NOTE: On the lower left corner of the switch frame, there is an air-gap switch. When servicing a controlled fixture,
pull lever out (OFF position). This will cut the power to the fixture. After servicing is complete, push the lever in (ON
position) to restore power. The lever must be pushed in all the way (ON position) for normal operation.
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your interior design requirements. Simply obtain a color
conversion kit of the appropriate color from your Leviton distributor and proceed as follows (please note that
wallplate must be removed).
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using a small screwdriver, gently remove the frame from the strap (refer to
Figure 2).
3. Take the new frame and position it properly to the strap. Notice that the frame has a cut-out for the air-gap switch
lever. Line up the plastic snaps with the square holes in the strap. Insert the snaps on one side of the frame into
the strap.
4. Firmly press sideways and down to slip the other snaps into place. The frame snaps in with a audible click.
Ensure that all four snaps are secure. Replace Decora
®
wallplate. The color conversion is complete.
TO OPERATE
ON:
Tap the upper half of the rocker. The lights will brighten to the last set light level.
OFF:
Tap the lower half of the rocker. The lights will dim to OFF.
BRIGHTEN:
Press and hold the upper half of the rocker to the desired light level.
FULL BRIGHT: If the lights are OFF, double tap the upper half of the rocker. The lights will turn ON FULL
BRIGHT.
If the lights are ON, tap the upper half of the rocker once. The lights will turn ON FULL
BRIGHT.
The previous light level will remain in memory upon next ON operation (see above).
FAST OFF:
Double tap the bottom half of the rocker. The lights will immediately turn OFF.
DIM:
Press and hold the lower half of the rocker to the desired level.
BRIGHTNESS LEVEL DISPLAY:
Indicates the level of brightness when the lights are ON. Indicates the previous level of brightness when the lights
are OFF (refer to Figure 1).
NOTE: To alert you that there is power to the dimmer when the load is OFF, the AC Indicator Light remains ON.
To alert you that the load is ON, the AC Indicator Light remains OFF.
NOTE: If lights are OFF, regardless if you tap or press and hold the upper half of the rocker, the lights will go to
last set light level.
NOTE: If a power interruption should occur while the device is ON, the light load will return to its previous light level
when power is restored within 10 seconds.
TROUBLESHOOTING
• Light does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Low-Voltage transformer is not connected to line Neutral.
- Overheated, correct load and allow dimmer to cool down and reset.
- Air gap switch is open.
• Dimmer does not operate
- Dimmer BLACK wire miswired to Low-Voltage Transformer and Dimmer BLUE wire miswired to LINE Hot.
• Light turns ON and Dimmer works, but remote does not work
- There are no connections from Remote to Dimmer.
- Remote miswired to Dimmer.
• Lights Flickering
- Lamp has a bad connection.
- Lamp power is less than 40W or 40VA.
DI-000-MDE03-00A
2
Figure 2 – Color Conversion
Brightness Level Display
Snaps
Push in 2 Locations
Air-Gap
Switch
Wiring Diagram 1 – Single Location Control Application
Cap with
Wire Connector
Hot (Black)
Line
120VAC, 60Hz
Neutral (White)
Wiring Diagram 2 – Two Location Control Applicatio
Mural
Dimmer
Hot (Black)
Black
White
Line
120VAC, 60Hz
Neutral (White)
Wiring Diagram 3 – Three Location Control Application
Mural
Dimmer
Hot (Black)
Blue
Black
Yellow
White
Line
120VAC, 60Hz
Green
Ground
Neutral (White)
DI-000-MDE03-00A
12/27/02, 4:14 PM
Frame
ON/OFF
LED
Strap
Mural
Dimmer
Blue
Yellow
Electronic
Low-Voltage
White
Transformer
Black
Black
Primary
Side
White
Green
Ground
n
Remote
MSEØR-1
Blue
Electronic
Low-Voltage
Yellow
Yellow
Transformer
Black
White
Primary
Side
White
Green
Green
Ground
Ground
Remote
Remote
MSEØR-1
MSEØR-1
Electronic
Yellow
Yellow
Low-Voltage
White
Transformer
White
Black
Primary
Side
White
Green
Green
Ground
Ground
Advertisement
