Deck Lift Assist Springs; Long Left Hand Deck Belt Replacement - Ferris ISX800 Series Operator's Manual

Zero-turn riding mower
Table of Contents

Advertisement

• If the measurements are greater than 4" (10,2 cm)
loosen the jam nut (D, Figure 55) and turn the fine
adjustment nut (E) counter-clockwise to lower the
deck.
• If the measurements are less than 4" (10,2 cm)
loosen the jam nut and turn the fine adjustment bolt
clockwise to raise the deck.
8. Once the 4" measurement from the front tip of the blade
is achieved, tighten the jam nut.
9. Loosen the nuts (F) that secure the rear hanger chain (G)
to the rear mounting plate (H) and allow the rear of the
deck to rest on the 2 X 4's and 1/4" (0,64 cm) spacers.
10. Repeat steps #7 - #9 for the other side of the unit.
11. Remove all blocking from beneath the mower deck.
12. Perform the Determining if the Deck Leveling Needs to
be Adjusted procedure to verify that the deck has been
leveled correctly.

Deck Lift Assist Springs

Some models are equipped with deck lift assist springs (A,
Figure 57) that assist the operator in raising the mower deck
with the deck lift pedal. The deck lift assist springs are factory
set to provide optimal lifting performance.
57
Although it is fastened with a multi-position anchor, this is not
an adjustment point.
Do NOT attempt to adjust the spring length or lifting
performance will be compromised.

Long Left Hand Deck Belt Replacement

NOTICE To avoid damaging belts, do not pry over
pulleys.
1. Park the unit on a smooth level surface such as a
concrete floor. Disengage the PTO, engage the parking
brake, turn the ignition switch to OFF, and remove the
ignition key.
2. Lower the mower deck to it's lowest cutting position and
remove the mower deck guards and floor pan to gain
access to the mower deck drive belts.
42
WARNING
Use extreme caution when rotating the idler arm with the
breaker bar, due to the increased tension in the spring
as the idler arm is being rotated. Injury may result if the
breaker bar is prematurely released while the spring is
under tension.
3. Using a 1/2" breaker bar (A, Figure 58) place the square
end in the opening in the PTO clutch drive idler arm (B)
and rotate the idler arm clockwise, which will relieve
tension on the belt exerted from the idler arm. Remove
the belt from the left hand side spindle pulley (C).
Carefully release the tension on the breaker bar.
58
4. Remove the long left hand belt (D) from the adjustable
idler pulley (E) and it's belt guide (F).
5. Remove the old long left hand belt from the PTO clutch
pulley (G) and the top groove of the center spindle pulley
(H).
6. Install the new long left hand belt onto the PTO clutch
pulley and the center spindle pulley.
7. Install the long left hand belt into the belt guide on the
adjustable idler pulley.
8. Verify that the V-side of the belt runs in the pulley grooves
of the center spindle pulley and the PTO clutch pulley.
Make sure that the back side of the belt contacts the face
of the adjustable idler pulley. Make sure that the belt is
correctly routed in the belt guides (F & I).
9. Using a 1/2" breaker bar place the square end in the
opening in the PTO clutch drive idler arm and rotate the
idler arm clockwise, which will relieve tension on the belt
exerted from the idler arm. Install the long left hand belt
onto the left hand spindle pulley. Carefully release the
tension on the breaker bar.
10. Measure the coil-to-coil length (A, Figure 59) of the long
left hand belt tensioning spring (B). The measurement
should equal 10-1/4" (26 cm) ± 1/8 (0,32 cm). If not,
www.ferrismowers.com

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents