Turn Indicators Connections; Standard Connections; Connections For Vehicles With Separate Lines; Connections To Hazard Switch - Gemini 823 Installation And Use Manual

6.0 -

TURN INDICATORS CONNECTIONS

6.1 - STANDARD CONNECTIONS

LEFT TURN
INDICATORS
ORANGE
GEMINI
ORANGE
SYSTEM
WHITE-ORANGE
WHITE-ORANGE wire must ONLY be
connected if the system is to operate via
the turn indicators.

6.2 - CONNECTIONS FOR VEHICLES WITH SEPARATE LINES

WHITE-ORANGE wire must ONLY be
connected if the system is to operate via
turn indicators.
WHITE-ORANGE
ORANGE
GEMINI
SYSTEM
ORANGE
2 Amp. diodes.
6.3 - CONNECTION TO HAZARD SWITCH
GEMINI
SYSTEM
PAGE 08 - INSTALLER MANUAL
RIGHT TURN
INDICATORS
TURN INDICATORS
CONTROL UNIT
Front Side Rear Rear Side
LH LH LH RH RH
Add 6
Select "optical pulse signals"
in the "SYSTEM
PROGRAMMING" menu.
Do not make this connection
BLUE
if the system is to operate
via turn indicators.
VEHICLE
WIRING
CIRCUIT

7.0 - SELECTABLE CONNECTIONS TO ARM/DISARM THE SYSTEM

Power door locks must be connected according to vehicle type (see installation specifications in the
restricted area of our website:
below and proceed with the applicable connection.
!
Arming via door lock motors.
!
Arming via door lock motors and door lock switches.
!
Arming via turn indicator flashes.
!
Arming via turn indicator flashes and door lock motors.
!
Arming via turn indicator flashes, door lock motors and lock switches
7.1 -

CONNECTION TO DOOR LOCK MOTORS WITH SEPARATE RADIO RECEIVER

Arm/disarm connections for vehicles where the remote control receiver is separate from the CDL
module (connection diagram "A" available in the restricted area of our website).
Set dip-switch N. 4 "ON".
7.2 - CONNECTION TO DOOR LOCK MOTORS WITH DOOR SWITCH
Arm/disarm connections for vehicles that require not only connections to the door lock motor unit but
also require control of the door switch or of the internal door lock buttons (
"D", "E" available in the restricted area of our website
Set dip-switch N. 4 "ON".
If the turn indicators lock/unlock flashes are identical, connect the door lock motors.
If the turn indicators flash when unlocking via the car mechanical key, do not make this
!
Front
To arm/disarm via the turn indicator flashes, connect the WHITE-ORANGE wire to the turn indicators.
RH
• If arming/disarming is only activated via the turn indicators, set dip-switch N. 4 "OFF".
• If arming/disarming is activated via the turn indicators and door lock motor unit, set dip-switch N. 4 "ON".
8.0 - HOW TO LEARN TURN INDICATOR LOCK/UNLOCK FLASHES
In order to arm/disarm via the turn indicators, the system must learn the vehicle lock (arm) and unlock
(disarm) flashes.
Connect the WHITE-ORANGE wire to the turn indicators and proceed as follows
!
Disconnect the 8-pin harness connector from the 8-pin alarm connector
!
Turn ignition key
!
Connect the 8-pin harness connector to the 8-pin alarm connector; the LED will turn ON steady
!
T urn ignition key
!
When the turn indicators stop flashing, a Beep will confirm the learning of the arming flashes
!
Press the unlock button on the vehicle original remote control
!
When the turn indicators stop flashing, 2 Beeps will confirm the learning of the disarming flashes
and the end of the procedure
www.gemini-alarm.com ). Check out the various possibilities described
).

7.3 - CONNECTION TO TURN INDICATORS

connection.
ON.
OFF, c lose all doors and press the lock button on the original remote control
.
.
connection diagrams "C",
:
.
.
.
.
.
INSTALLER MANUAL - PAGE 09