1. Manuals
  2. Brands
  3. Gemini Manuals
  4. Car Alarm
  5. 822 Series
  6. Installation and use manual

Gemini 822 Series Installation And Use Manual

Hide thumbs Also See for 822 Series:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION CERTIFICATE
The undersigned qualified installer attests to have personally fitted the here described vehicle
security system following the manufacturer instructions.
By :
Sold on :
................................................
Vehicle :
..........................................................................................................................
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
www.gemini-alarm.com
ISO 9001 Certified Company
823
Type of product :
822
SERIE 823
INSTALLATION AND
USE MANUAL
Made in Italy
823
822
UK
AC 2711UK Rev. 06 - 10/14

Advertisement

Table of Contents
loading

Related Manuals for Gemini 822 Series

Summary of Contents for Gemini 822 Series

  • Page 1 ..........Vehicle : INSTALLATION AND .......................... USE MANUAL GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com AC 2711UK Rev. 06 - 10/14 Made in Italy...

  • Page 2: Preliminary Advice

    USER MANUAL Before installing, identify your alarm model and refer to it for the correct instructions - SYSTEM OPERATION....................PAGE 03 GEMINI 822: same as 823 without self-powered battery. 2.1 - Complete system arming..................PAGE 03 The following signs, intended for the installer or the user, indicate particular functions or connections: 2.2 - System arming with sensor and comfort control exclusion........

  • Page 3: Warranty Conditions

    2.6 - ALARM, INHIBIT TIME BETWEEN ALARMS AND ALARM CYCLES The guarantee is valid exclusively at authorized Gemini Technologies Service Centers. The system will indicate an alarm event via optical/acoustic signals.

  • Page 4: Pinout Tables

    INSTALLER MANUAL 6.0 - WIRING DIAGRAM 5.0 - PINOUT TABLES Before starting any 5.1 - 20-PIN CONNECTOR electrical work, disconnect the negative POSITION WIRE FUNCTION WIRE COLOUR battery terminal. Reconnect only after - 1 - Door pin switch input (negative) YELLOW-RED Connection completing the wiring...
  • Page 5 8.1 - CONNECTION TO DOOR LOCK MOTORS WITH SEPARATE RADIO RECEIVER SYSTEM WHITE-ORANGE Arm/disarm connections for vehicles with a radio receiver that is separate from CDL (see www.gemini- alarm.com for diagram “A” connection). Set dip-switch N. 4 “ON”. WHITE-ORANGE wire must ONLY be 8.2 -...
  • Page 6 10.7 - NEGATIVE OUTPUT SELECTION (DURING ALARM) FOR HORN OR ADDITIONAL 10.0 - SYSTEM PROGRAMMING SIREN The t able below applies to the system programmed in “standard configuration”. Depending on the connection made, this feature can activate the output for the siren (continuous tone) very time you enter the programming procedure, the alarm resets to the default settings or for the horn (intermittent tone FUNCTION...
  • Page 7 12.0 - DIP-SWITCHES PROGRAMMING TABLE 14.0 - ADDING NEW DEVICES Set dip-switches BEFORE connecting the alarm system. To carry out the operation successfully, make sure the required electrical connections If settings must be modified after installation, FIRST disconnect the alarm and then (door/bonnet switches and ignition) are complete.

  • Page 8: Technical Specifications

    15.0 - DELETING PROGRAMMED DEVICES 16.0 - SYSTEM RESET With this procedure all settings will be returned to the factory default settings. To carry out the operation successfully, make sure the required electrical connections (door/bonnet switches and ignition) are complete. Reset must therefore only be carried out in case of need, before programming the system or learning the turn indicator flashes.

This manual is also suitable for:

823 series

Table of Contents