Gemini 823 Installation And Use Manual
  1. Manuals
  2. Brands
  3. Gemini Manuals
  4. Car Alarm
  5. 823 Series
  6. Installation and use manual
Gemini 823 Installation And Use Manual

Gemini 823 Installation And Use Manual

Hide thumbs Also See for 823:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION CERTIFICATE
The undersigned qualified installer attests to have personally fitted the here described vehicle
security system following the manufacturer instructions.
By :
Sold on :
................................................
Vehicle :
..........................................................................................................................
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia
Tel. +39 0332 943211
www.gemini-alarm.com
ISO 9001 Certified Company
823
Product type :
822
INSTALLATION AND
USE MANUAL
Made in Italy
823
822
UK
AC2711/UK Rev.07 - 04/22

Advertisement

Table of Contents
loading

Related Manuals for Gemini 823

Summary of Contents for Gemini 823

  • Page 1 Product type : ..........INSTALLATION AND Vehicle : USE MANUAL .......................... GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia Tel. +39 0332 943211 www.gemini-alarm.com AC2711/UK Rev.07 - 04/22 Made in Italy ISO 9001 Certified Company...

  • Page 2: Table Of Contents

    - SYSTEM OPERATION....................PAGE 03 822: same as 823 without self-powered battery. 2.1 - System total arming....................PAGE 03 The following signs are used throughout the manual to emphasize important instructions or special 2.2 - System partial arming....................

  • Page 3: Arming Delay

    2.4 - ARMING DELAY 3.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT There is a 30 sec. activation delay from the time the system is armed to allow you to exit the vehicle The present device falls within the field of application of the current WEEE Directive. The crossed-out without setting off an alarm.

  • Page 4: Installer Manual

    INSTALLER MANUAL 5.0 - WIRING DIAGRAM 4.0 - CONNECTOR PINOUTS Before carrying out 20-PIN CONNECTOR electrical connections, disconnect the negative POSITION WIRE FUNCTION WIRE COLOUR battery terminal and re- connect only after - 1 - Door pin switch input (negative) YELLOW-RED completion.

  • Page 5: Turn Indicators Connections

    Power door locks must be connected according to vehicle type (see installation specifications in the 6.1 - STANDARD CONNECTIONS restricted area of our website: www.gemini-alarm.com ). Check out the various possibilities described below and proceed with the applicable connection. LEFT TURN RIGHT TURN Arming via door lock motors.

  • Page 6: System Programming

    The LED will power ON for approx. 2 sec.; while the LED is ON, touch the override key to its Passive arming isabled receptacle For Gemini only Key OFF/ON Boot input, positive signal isabled Optical pulse signals (Hazard flashers) isabled...

  • Page 7: 11.0 - Dip-Switch Settings

    11.0 - DIP-SWITCH SETTINGS 13.0 - PROGRAM NEW DEVICES Set dip-switches BEFORE connecting the alarm system. To carry out the operation successfully, make sure the required electrical connections If settings must be modified after installation, FIRST disconnect the alarm and then (door/bonnet switches and ignition) are properly connected.

  • Page 8: Delete Programmed Devices

    Close the bonnet and k eep it closed for at least 8 sec. to fully clear the memory. 16.0 - TECHNICAL SPECIFICATIONS Power supply 823 - 822 12 Vdc If the bonnet is opened before 8 seconds, devices will not be deleted.

This manual is also suitable for:

822

Table of Contents