Description (Fig. A); Operation; Operating Tips; Assembly And Adjustments - DeWalt DCLE34021 Original Instructions Manual

EngLIsh
v
Only for indoor use.
x
Discard the battery pack with due care for
the environment.
y
Charge D WALT battery packs only with designated
e
D WALT chargers. Charging battery packs other than
e
the designated D
e
charger may make them burst or lead to other
dangerous situations.
z
Do not incinerate the battery pack.
Battery Type
The following tools operate on a 18 volt battery pack:
DCLE34021, DCG416VS
These battery packs may be used: DCB181, DCB182, DCB183,
DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185,
DCB187, DCB189, DCBP034, . Refer to Technical Data for
more information.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Battery
1
Battery release button
2
Horizontal laser line on/off button
3
Vertical laser line on/off button
4
Pendulum locking switch
5
Magnetic pivot bracket
6
Keyhole slot
7
8 Laser window
Laser label location
9

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. C).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
30
WALT batteries with a D WALT
e
1 is fully charged.
2 and firmly pull the
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 14 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect before making
any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.

OPERATING TIPS

• To extend battery life per charge, turn the laser off when it is
not in use.
• To ensure the accuracy of your work, check the laser calibration
often. Refer to Checking Laser Accuracy.
• Before attempting to use the laser, make sure it is positioned
securely, on a smooth, flat stable surface that is level in
both directions.
• To increase beam visibility, use a Laser Target Card (Figure N)

CAUTION: To reduce the risk of serious injury, never stare
directly into the laser beam with or without these glasses.
Refer to Accessories for important information.
• Always mark the center of the beam created by the laser.
• Extreme temperature changes can cause movement or shifting
of building structures, metal tripods, equipment, etc., which
can effect accuracy. Check your accuracy often while working.
• If the laser has been dropped, check to make sure your laser is
still calibrated. Refer to Checking Laser Accuracy.
Turning the Laser On (Fig. D)
With the laser off, place it on a flat surface. This model has a
pendulum locking switch 5
beams with two ON/OFF buttons; one for a horizontal laser line
and one for a vertical laser line
on by moving the pendulum lock switch to the UNLOCKED/
ON position and pressing the required ON/OFF button on the
keypad. The laser lines can be powered one at a time or at the
same time. Pressing the ON/OFF buttons again turns the laser
lines off. The pendulum locking switch disables the lasers as well
and a keypad to activate the laser
. Each laser line is powered