Download
Share
Print this page
Exmark UltraVac 126-8680 Setup Instructions
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn and Garden Equipment
  5. Ultravac Bagger 126-8680
  6. Setup instructions

Exmark UltraVac 126-8680 Setup Instructions

Bagger
Hide thumbs Also See for UltraVac 126-8680:
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Important: Due to the added weight of the Ultravac, it is important to ensure the parking brake on your
mower is adjusted properly. Before installing the Ultravac, make sure to re-adjust the parking brake on
your mower as outlined in the "Adjusting the Parking Brake" procedure in the Maintenance section of
the mower Operator's manual.
Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part No.
—
Literature Pack
Manual-Operator's
Models and Required Completing Kits
Completing Kits
Note: Use the following charts to verify the kits required for the machine you are installing the UltraVac on.
Deck
80T-60 (60 inch deck with 80T Engine)
80T-72 (72 inch deck with 80T Engine)
88C-60 (60 inch deck with 88C Engine)
88C-72 (72 inch deck with 88C Engine)
© 2019—Exmark Mfg. Co., Inc.
2101 Ashland Ave
Beatrice, NE 68310
Description
ULTRAVAC
For Ultravac Serial Nos. 406,294,345 & Higher
(To fit Lazer Z Diesel Units Serial Nos. 790,000 & Higher)
Qty.
Fill out the online warranty registration
form.
Completing Kit
126-8675
126-8677
126-8676
126-8678
All Rights Reserved *4504-789* A
Part No. 4504-789 Rev. A
Printed in the USA.
BAGGER
®
126-8680
Setup Instructions
Use

Advertisement

loading

Related Manuals for Exmark UltraVac 126-8680

Summary of Contents for Exmark UltraVac 126-8680

  • Page 1 126-8677 126-8676 88C-60 (60 inch deck with 88C Engine) 88C-72 (72 inch deck with 88C Engine) 126-8678 © 2019—Exmark Mfg. Co., Inc. All Rights Reserved *4504-789* A Part No. 4504-789 Rev. A 2101 Ashland Ave Printed in the USA. Beatrice, NE 68310...
  • Page 2 Adjusting the Parking Brake Re-adjust the parking brake on your mower as outlined in the “Parking Brake Adjustment” procedure in the Maintenance section of the mower Operator's manual. Installing the Mount Brackets Install a lower mount bracket on the left and right side of the rear bumper cross tube as shown in Figure 1.
  • Page 3 installed or removed in their entirety. Do Not operate the mower with only a portion of the UltraVac installed. Installing the Belt Cover Bracket Lower the deck fully. Remove and retain the standard right side belt cover, wireform bracket and its hardware.

  • Page 4: Installing The Blower Assembly

    Apply a light coat of Mobil HTS grease (or food grade antisieze) to the top portion of the spindle shaft where the sheave mounts. Install double sheave onto the right spindle shaft. Install the spring disc washer and nut. Make sure that the spring disc washer cone is installed towards nut (see Figure 5).
  • Page 5 g242180 Figure 8 1. Blower 3. Mower frame 2. Belt cover g242492 Figure 10 1. Lower bagger mount bar 2. Frame leg Push down on the back of the cover and slide it backwards under the blower. Lift the hopper assembly and pivot it upward towards With the belt cover resting on the deck, slide it the back of the machine.
  • Page 6 Assembling the Tubes Slide the lower tube onto the blower and attach the latches. (Make sure that the upper tube does not For 60 inch decks, shorten the upper tube. move out of alignment). Locate the three holes in the upper tube. Measure Drill the 7/32 inch (5.6 mm) diameter holes in the 6 1/2 inches (165 mm) up from the end of the lower tube using the upper tube holes as reference.