Panasonic AG-DV2500P Service Manual page 25

(2) Error code description
Error code
0201 CONDENSATION ON DRUM
3200 LOADING FAILURE
3300 UNLOADING FAILURE
No display
4100 CASSETTE EJECT FAILURE
5605 DEFECTIVE TAPE
5606 DEFECTIVE TAPE
5607 DEFECTIVE TAPE
5608 DEFECTIVE TAPE
5609 DEFECTIVE TAPE
5702 TAPE END DET. ERROR
5802 TAPE BEGIN DET. ERROR
7001 DRUM MOTOR FAILURE
7101 CAP MOTOR FAILURE
7202 SUPPLY REEL FAILURE
7203 SUPPLY REEL FAILURE
7302 TAKE UP REEL FAILURE
7303 TAKE UP REEL FAILURE
7305 TAKE UP REEL FAILURE
7401 REEL MOTOR FAILURE
1-14
Display Content of occurrence
DEW detected
Does not load
Does not unload
Does not intake
Does not eject
Tape abnormality
during intake
Tape tear during
unloading
Tape tear during
loading
Tape tear on the
loading side
Tape tear during
slack takeup
End sensor
malfunction
Begin sensor
malfunction
Drum motor does
not rotate
Capstan motor
does not rotate
SUP reel does not
rotate
SUP side tape slack
TU reel does not
rotate
TU side tape slack
Tape slack during
unloading
Reel motor does
not rotate
Table 1.8.7 (3) Error Code Contents
Method of detection
If DEW sensor detects
condensation
If mechanism position does
not move in loading direction
within 5 seconds
If mechanism position does
not move in unloading
direction within 5 seconds
If intake is not completed
within 5 seconds (Perform
ejects without warning)
If eject is not completed
within 5 seconds
If begin and end sensor are
ON after intake
If reel FG is excessive during
unloading
If reel FG is insufficient during
loading
If only supply side reel does
not rotate during FWD/REV
If tape slack takeup is not
completed within 10 seconds
If trailer tape sending is not
completed within 3 seconds
If leader tape sending is not
completed within 3 seconds
If drum motor does not rotate
for over 4 seconds
If capstan motor does not
rotate for over 2 seconds
If SUP reel does not rotate for
over 3 seconds
If only SUP reel does not
rotate during REV
If TU reel does not rotate for
over 3 seconds
If only TU reel does not rotate
during FWD
If TU reel FG is insufficient
during unloading
If reel motor does not rotate
for more than 4 seconds
during reel drive mode
Detected signal
IC302 (MSD) –detects
voltage of pin 318
IC302-pin354
Rotary encoder output is
detected
IC302-pin354
Rotary encoder output is
detected
IC302 (MSD) –pin 84,
CASSETTE SW is not
detected within 5 seconds
IC302 (MSD) –pin 26,
HOUSING SW is not
detected within 5 seconds
IC302 (MSD) –pin 278, START
sensor and pin 297,
END sensor are both detected
IC302 (MSD) –pin 75, TU
REEL FG is detected
IC302 (MSD) –pin 75, TU
REEL FG is detected
IC302 (MSD) –pin 72, SUP
REEL FG is not detected
IC302 (MSD) –pin 75, TU
REEL FG and pin 72, SUP
REEL FG are both detected
IC302 (MSD) –pin 297, END
sensor is detected for over 3
seconds
IC302 (MSD) –pin 278,
START sensor is detected for
over 3 seconds
IC302 (MSD) –pin 55, DRUM
FG is not detected for over 4
seconds
IC302 (MSD) –pin 56, CAP
FG is not detected for over 2
seconds
IC302 (MSD) –pin 72, SUP
REEL FG is not detected for
over 3 seconds
IC302 (MSD) –pin 72, SUP
REEL FG is not detected
IC302 (MSD) –pin 75, TU
REEL FG is not detected for
over 3 seconds
IC302 (MSD) –pin 75, TU
REEL FG is not detected
IC302 (MSD) –pin 75, TU
REEL sensor is detected
IC302 (MSD) –pin 91, REEL
FG is not detected for over 4
seconds