Panasonic AG-DV2500P Service Manual page 248

Pin No. Port Name
51 P41/AN1
52 P40/AN0
53 Vref
54 AVCC
55 MD0
56 MD1
57 OSC2
58 OSC1
59 RES
60 NMI
61 STBY
62 VCC
63 XTAL
64 VSS
65 EXTAL
66 FEW
67 MD2
68 PF7/"
69 PF6
70 PF5
71 PF4
72 PF3/-ADTRG/IRQ3
73 PF2
74 PF1/BUZZ
75 PF0/IRQ2
76 P30/TxD0
77 P31/RxD0
78 P32/SCK0/SDA1/IRQ4
79 P33/TxD1/SCL1
80 P34/RxD1/SDA0
81 P35/SCK1/SCL0/IRQ5
82 P36
83 P77/TxD3
84 P76/RxD3
85 P75/TMO3/SCK3
86 P74/TMO2/MRES
87 P73/TMO1
88 P72/TMO0
89 P71/TMRI23/TMCI23
90 P70/TMRI01/TMCI01
91 PG0/IRQ6
92 PG1/IRQ7
93 PG2
94 PG3
95 PG4
96 PE0
97 PE1
98 PE2
99 PE3
100 PE4
Reference
METER_CH1
METER_CH2
Analog reference
Analog power
Mode terminal 0
Mode terminal 1
Subclock (32.768kHz)
Subclock (32.768kHz)
Reset input
NMI
Standby
Power
Clock
Power
External clock
Flush light enable
Mode terminal 2
System clock (TP2002)
SWIN_NTSC
TP2021
FAN_STOP (H)
OPERATE
EJECT
TP2023
WAKE_UP
OSD_DATA
OSD_CS
OSD_CLK
422_Tx
422_Rx
8029VD
OSD_RST
MS_OUT
MS_IN
MS_CLK
SCR_LR
SCR_UD
V_MUTE
MSD_RESET
MSD_CS
SYS_OUTV
SYS_INV
MSD_READY
8029CS
8029CLK
8029SDI
8029SDO
8029RST
8029AMUTE
V_PB (H)
Table 4.3.2 SYSCON Terminal Function
I/O
I AUDIO indicator
I
-
+3V
I Pullup (not used)
I Pullup (not used)
I X2002
I
I From IC2004
I Pullup (not used)
I Pullup (not used)
+3V
I X2001
GND
I X2001
I For Rewrite
I Operation mode setup
O
I REAR NTSC/PAL slid SW
Not used
I Not used
I Operate SW
I Pull-up from EJECT SW AL3V
- Not used
I Start interrupt key input from standby mode
O OSD (UART0)
O
O
O RS-422 (UART1)
I
I IC208 CSYNC
O OSD
O MS BUS (UART3)
I
O
I Not used
I Not used
O
Reset output to VCR (MSD) microcomputer
O Interface with VCR (MSD) microcomputer
I VIDEO V TIMING
I
O Interface with VCR (MSD) microcomputer
O IC208 control
O
O
I
O
O
O VIDEO
Description
4-7