Easy Mode/Dsp Operations; Dsp Effect On/Off; Calling Dsp Basic Pattern/User Pattern; Setting And Storing Dsp Properties/Memory Into User Pattern - Clarion VRX6671Z Owner's Manual & Installation Manual

8. Operate the JOYSTICK ¡ rightward or left-
ward to select "MENU" and press the ENT at
the center of the JOYSTICK ¡ to change into
the AUDIO-MODE display.

Easy mode/DSP operations

DSP effect ON/OFF

The factory default setting is "ON".
1. Press the A-M button & to show the AUDIO-
MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "DSP ON/OFF". "ON" and
"OFF" items are displayed in the menu bar.
3. Operate the JOYSTICK ¡ rightward and left-
ward to select "ON" or "OFF" and press the
ENT at the center of the JOYSTICK ¡ to set
it.
Note:
• If the DSP effect is set to OFF, the adjustment
made in "DSP operations" is not reflected in the
music source.
Calling DSP BASIC Pattern/USER
Pattern
1. Press the A-M button & to show the AUDIO-
MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "DSP MODE". "BASIC 1", "BA-
SIC 2" and "USER" items are displayed in the
menu bar.
3. Operate the JOYSTICK ¡ rightward or left-
ward to select the item thus called, and press
the ENT at the center of the JOYSTICK ¡ to
show BASIC pattern selecting display or
USER pattern selection/memory display.
4. In the pattern selecting display, operate the
JOYSTICK ¡ rightward or leftward to select
P1 to P6, and press the ENT at the center of
the JOYSTICK ¡ to call corresponding DSP
mode. In this display, pressing the No. button
in correspondence to the PRESET buttons #
can also call the DSP mode.
After selecting P1 to P6 by operating the JOY-
STICK ¡, press the ENT at the center of the
JOYSTICK ¡ for 2 seconds or longer to copy
the selected pattern to the USER pattern.
Operate the JOYSTICK ¡ rightward or left-
ward to select "EDIT", and press the ENT at
the center of the JOYSTICK ¡ to show DSP
adjusting display, in which the properties of cur-
rently selected pattern can be adjusted.
By pressing the BAND button % in BASIC pat-
tern selecting display or USER pattern selec-
tion/memory display you can switch between
the two patterns, BASIC and USER.
5. Operate the JOYSTICK ¡ rightward or left-
ward to select "MENU", and press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
Setting and storing DSP Properties/
Memory into USER Pattern
1. Repeat the steps 1 to 3 of the previous proce-
dure (Calling DSP BASIC Pattern/USER Pat-
tern) to show BASIC pattern selecting display
or USER pattern selection/memory display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "EDIT", and press the ENT at
the center of the JOYSTICK ¡ to show the
DSP adjusting display.
3. Select an item to be adjusted by operating the
JOYSTICK ¡ rightward or leftward in the DSP
adjusting display.
"EF" EFFECT
"DL" DELAY
"R.M" REAR MIX
"R.S" ROOM SIZE
"LV" LIVENESS
"R.T" REVERB TIME
"HI" HIGH
4. Operate the JOYSTICK ¡ upward or down-
ward to set each adjusting value.
By pressing the PRESET buttons # once in
the DSP adjusting display, the setting value for
currently stored USER pattern is obtained.
5. After making adjustments to a desired pattern
by repeating the operations of items 3 and 4,
operate the JOYSTICK ¡ rightward or left-
ward to move the cursor to "RTN", and press
the ENT at the center of the JOYSTICK ¡ to
change over to the BASIC/USER pattern se-
lection/memory display.
6. Operate the JOYSTICK ¡ rightward or left-
ward in the BASIC/USER pattern selection/
memory display to select USER memory P1 to
P6 to be stored, and press the ENT at the cen-
ter of the JOYSTICK ¡ for 2 seconds or longer
to store the adjusted DSP pattern to the USER
memory.
By pressing the PRESET buttons # 1 to 6 for 2
seconds or longer in the DSP adjusting display, the
DSP pattern can be stored in the USER memory.
DSP operations
35
VRX6671z