Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel OB30SP
Summary of Contents for Fisher & Paykel OB30SP
- Page 1 BUILT-IN OVEN OB30SP & OB30DP models INSTALLATION GUIDE US CA...
-
Page 2: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! Electric Shock Hazard Cut Hazard Failure to follow this advice may result in Failure to use caution could result in injury. electric shock or death. • Take care – some panel edges are sharp. • Before carrying out any work on the electrical WARNING! section of the appliance, it must be disconnected To avoid hazard, follow these instructions carefully before installing or using this appliance. -
Page 3: Parts Supplied
PARTS SUPPLIED Screws Spacers Long Trim (1) Single oven models (2) Single oven models (2) To be fitted in Double oven models (4) Double oven models (4) a flush installation. PRIOR TO INSTALLATION IMPORTANT! Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cavity. -
Page 4: Product Dimensions - Single Ovens
PRODUCT DIMENSIONS — SINGLE OVENS FRONT PROFILE OB30S PRODUCT DIMENSIONS INCHES A Overall height of product 27 1/8 B Overall width of product 29 13/16 C Overall depth of product (excl. handle and dials) 23 15/16 D Depth of oven front and control panel (excl. handle and dials) 1 9/16 E Depth of chassis (does not include oven front) 22 3/8... - Page 5 CABINETRY DIMENSIONS — SINGLE OVENS PROUD INSTALL 5/8 – 13/16" (16-20mm) spacer Electrical Supply 1 – 5/8" (42mm) min 1/16" (2mm) PROFILE PLAN FLUSH INSTALL OB30S CABINETRY DIMENSIONS INCHES A Minimum inside width of cavity 28 1/2 5/8 – 13/16" B Overall width of cabinetry 30 1/8 (16-20mm) C Minimum inside height of cavity 26 13/16 spacer...
-
Page 6: Product Dimensions - Double Ovens
PRODUCT DIMENSIONS — DOUBLE OVENS FRONT PROFILE OB30D PRODUCT DIMENSIONS INCHES A Overall height of product 48 1/2 1232 B Overall width of product 29 13/16 C Overall depth of product (excl. handle and dials) 23 15/16 D Depth of oven front and control panel (excl. handle and dials) 1 9/16 E Depth of chassis (does not include oven front) 22 7/16... - Page 7 CABINETRY DIMENSIONS — DOUBLE OVENS PROUD INSTALL 5/8 – 13/16" (16-20mm) Electrical spacer Supply 1 – 5/8" (42mm) min 1/16" (2mm) FLUSH INSTALL PROFILE PLAN OB30D CABINETRY DIMENSIONS 5/8 – 13/16" INCHES (16-20mm) A Minimum inside width of cavity 28 1/2 B Overall width of cabinetry spacer 1 – 5/8" (42mm) C Minimum inside height of cavity 48 3/16...
-
Page 8: Unpacking The Oven
UNPACKING THE OVEN Single model shown for illustration purposes only IMPORTANT! When you remove the oven from the carton be careful not to damage the lower trim. The trim is important for both ventilation and to ensure the door opens fully without obstruction. Ensure you remove the Long Trim from the packaging. - Page 9 REMOVING AND REFITTING THE DOOR(S) IMPORTANT! Take care, the oven door is heavy. Do not lift the oven door by its handle. Doing so may damage the door. Ensure the oven and the door are cool before you begin to remove the door. Before removing the door, ensure there is a large enough clear, protected surface in the kitchen to rest the door on.
- Page 10 ELECTRICAL CONNECTION TO JUNCTION BOX Nameplate location Junction box locations MAX CURRENT MODEL VOLTAGE MAX LOAD DRAW OB30 Single 208 V 16.6 A 3.5 kW 240 V 19.4 A 4.6 kW junction box location for OB30 Double 208 V 33.2 A 7.0 kW undercounter installation...
-
Page 11: Secure The Oven To The Cabinetry
SECURE THE OVEN TO THE CABINETRY IMPORTANT! Do not lift the oven by the door handle. Do not over-tighten the screws. Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal. - Page 12 FLUSH INSTALLATION ONLY — REPLACE THE LOWER TRIM WITH THE SUPPLIED LONG TRIM Unscrew and remove Replace with the the installed lower trim supplied long trim...
-
Page 13: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER TEST OPERATION: Ensure the oven is level and securely fitted to the cabinetry. Turn the power to the oven on. The display should light up. Check the lower trim is undamaged. Set the clock following the instructions in the ‘User guide’. Open the oven door slowly until it is fully open and check there is Set the oven to Bake at 120°F (50oC). - Page 14 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.