Page 2
B. Objects have fallen, liquid has been spilled into the appliance; or appliance. C. The appliance has been exposed to rain; or If you have any questions please call Russound Inc. at 1-800-638-8055 or 603-659-5170. D.The appliance does not appear to operate normally; or Safety Instructions: E.
TABLE OF CONTENTS USER SECTION Product Introduction ......................5 Component Guide CAA66 Controller ........................6 KP6 Keypad........................7 KPL Keypad ........................8 KPSC Keypad........................9 Numeric Entry........................9 Prefix and Suffix Commands ...................9 SRC1 Remote Control......................10 Operation KP6 User Options Mode ....................11 KPL User Options Mode.....................12 INSTALLER SECTION Getting Started Unpacking ........................13...
Page 4
TABLE OF CONTENTS Common IR Input Connection .....................22 Speaker Connections ......................23 Zone Fixed/Variable Audio Output ..................24 12VDC Mute Trigger In/Trigger Out ..................25 Controller Link In/Out ......................26 RS-232 Interface .......................27 Initial Hardware Install Test ....................28 Programming Programming Center ......................29 Controller Setup Mode Controller ID .......................30 Number of Sources.....................31 Factory Initialization.....................32...
INTRODUCTION Thank you for choosing the Russound CAA66 • Scalable to 36 zones by connecting multiple ® controller amplifier to enhance your home with CAA66 units, to make whole-house audio avail- distributed audio. able to larger homes. Your system can grow as your home grows.
COMPONENT GUIDE CAA66 FRONT PANEL The CAA66 front panel consists of a split molded “power on” indicator to the left which illuminates when piece with a removable bottom half. This bottom piece the unit is on. The six zone LEDs light up amber when hides the Programming Center buttons.
COMPONENT GUIDE KP6 KEYPAD KP6 Keypad SOURCE NAME - Six clear windows with replaceable source name labels. Current source selected is backlit amber. VOLUME UP - Raises the volume for the room/adjusts User Menu options. VOLUME DOWN - Lowers the volume for the room/adjusts User Menu options. POWER - Turns zone ON or OFF when pressed once.
COMPONENT GUIDE KPL KEYPAD KPL Keypad LCD PANEL - 5-character amber backlit display shows source name, volume and zone status. VOLUME UP - Raises the volume for the room/adjust User Menu options. VOLUME DOWN - Lowers the volume for the room/adjust User Menu options. POWER - Turns zone ON or OFF when pressed once.
COMPONENT GUIDE KPSC KEYPAD KPSC Source Control Keypad The KPSC keypad connects to a KP6 or KPL key- A second press of the Numeric button sends a pad to add source control and numeric capabili- Suffix command of “Enter” and puts the keypad ty.
COMPONENT GUIDE SRC1 SYSTEM REMOTE CONTROL POWER - Turns on or off selected zone. NUMERIC INPUT - Number buttons for direct input of frequency, channel, etc. VOLUME UP/DOWN - Raises or lowers the vol- ume in the zone. MUTE - Mutes/unmutes zone audio output. INFO - Displays current channel and program information.
OPERATION USER OPTIONS SETTINGS KP6 Keypad User Options Mode Operation Source window blinks to indicate the option that is ready for adjustment Bass Treble Balance Turn On Volume Option setting level Press and hold Source Press Volume button to Up or Down enter or exit buttons to User Options...
OPERATION USER OPTIONS SETTINGS KPL Keypad User Options Mode Operation Press and Press Volume hold Source Up or Down button to buttons to enter or exit adjust setting User Options Mode Press Source button to select option Blue LED will blink to indicate Loudness is ready for adjustment KPL User Options Mode...
• Check for any visible signs of damage. If you • What are the intended listening zones? encounter any concealed damage, consult your • What system options and accessories might Russound dealer before proceeding to install the be required for features such as local sources, unit. etc.? •...
INSTALLER WIRING INSTRUCTIONS RJ-45 Connections The CAT-5 T568A wiring standard shown on the right is used for the RJ-45 terminations. Keypad Wiring For the KP6 or KPL keypad, the following con- • Confirm ahead of time that you can drill an nections are used to terminate the CAT-5 wire to outlet hole easily and in an unobtrusive spot the 110 punchdown on the keypad:...
INSTALLER COMPONENT GUIDE Controller Front Panel Removal Front Panel Removal this may require moving it until the front edge hangs The CAA66 front panel removable bottom half hides clear of the shelf. the Programming Center. It is important to follow the proper removal process to remove the panel without Place a flat screwdriver blade in the bottom slot on damage.
INSTALLER COMPONENT GUIDE Controller Back Panel CONTROLLER LINK IN AND LINK OUT - Links multiple CAA66 controllers and peripherals. RS-232 INTERFACE - The RS-232 Interface allows the zones to be controlled by PC or other devices that have an RS-232 Interface, allows for firmware updates and programming. CPU UPDATE SWITCH - For firmware updates.
KP6 and KPL keypad operating system firmware. If an update is released, it will be available online through the Document Center on www.russound.com. Look in the “Firmware and Downloads” section under Multi-Zone product type. The Advanced Programming Cable is available from Russound, Part #2500-521065.
INSTALLER COMPONENT GUIDE Keypad Rear Panel and Installation CAT-5 to KP6/KPL Connection if the terminations deviate from the The KP6/KPL keypad uses a 110- required connection order. punchdown terminal on the back Take care when using an impact 110 panel to provide simple installation punchdown tool, as this may over- and a strong connection for CAT-5 spread the contact points.
INSTALLER MAKING CONNECTIONS Keypad Port Connection The Keypad Ports are located on the back of If using more than one keypad in a zone, use an the CAA66 in the top left of center. Connections SA-ZX3 System Keypad Splitter (optional). The at the Keypad Ports are made with RJ45 con- SA-ZX3 supports up to three keypads per zone nectors using T568A CAT-5 wire configuration.
Source Audio and IR Connections Source Audio Connections The CAA66 supports up to six audio sources. The 1. Using an IR emitter (the Russound 845.1 is Source Inputs are located on the back panel. recommended) attach the end of the emitter Connect each source using quality RCA signal ”...
RNET Link In/Out Connections The CAA66 supports source control of The RNET components are linked to the con- Russound RNET components (ST2 Smart Tuner, troller and each other using RJ45 patch cables SMS3 Smart Media Server) through the connected to the Link In and Link Out ports.
Common IR Connection Common IR Connections The Common IR jack on the rear of the CAA66 The Russound 845.1 single IR emitter is recom- allows control of any source equipment without mended, or use an IR connecting block such as that source being selected on the keypad.
INSTALLER MAKING CONNECTIONS Speaker Connections The speakers are connected to the CAA66 using WHITE -- L+ (left channel positive) modular snap connectors. Each of these color- GREEN -- L- (left channel negative) coded connectors is designated for the speaker set of a particular amplified zone. To avoid con- BLACK -- R- (right channel negative) fusion, connect one zone speaker set at a time RED -- R+ (right channel positive)
1 and Zone 2. Each of these zone audio output if additional amplification is desired (e.g., connections features a stereo line out RCA con- Russound R235LS two-channel amplifier). Use nection plus a switch to allow for either a fixed quality RCA signal cables to ensure a constant or a variable line level output.
INSTALLER MAKING CONNECTIONS 12VDC Mute Trigger In/System Trigger Out 12VDC Mute Trigger In 12VDC System Trigger Out When 12VDC is applied to the Mute In, the sys- Trigger Out 12VDC output is used for triggering tem will fully mute all zones in the system. The an external amplifier or other component.
INSTALLER MAKING CONNECTIONS Controller Link In and Link Out Controller Link In/Out The Controller Link In and Link Out can be used Note: If two or more CAA66 controllers will be to connect up to six CAA66 controllers. The con- connected using the Controller Link In and Link nection is made using a CAT-5 patch cable from Out ports, each controller must have a unique...
PC application, see the Document PC for control and firmware updates of the con- Center at www.russound.com . Look for the troller. The RS-232 com port is located on the Technical Documents under Multi-source/Multi- back of the CAA66 and uses a DB-9 cable con- zone products.
4. Check to see that the keypad is connected to the Zone #1 Keypad Port and verify the CAT-5 is properly terminated at both ends. If none of these steps produce successful results, call Russound Tech Support for further assistance.
INSTALLER PROGRAMMING OVERVIEW Programming Center The CAA66 and its connected sources are configured IR/Learn) and are accessed with a press of the Setup through the Programming Center, located on the front button. of the CAA66 behind the removable lower panel. The The SRC1 system remote control is used to enter LEDs are dual purpose with different colors to indicate information during the setup procedures, and the LEDs...
INSTALLER KPL SETUP AND DIAGNOSTIC MENUS KPL Setup Menu The KPL Setup menu is used to choose source names, check the version number and perform a Factory Initialization of the CAA66 controller. The menu is outlined in the diagram to the right. To access the Setup Menu, press and release the Setup button on the right side of the keypad until...
Page 46
Aiwa 0157 One For All 0167 Device Codes for Tuner/Amp: Cal i f orni a Audi o Labs 0029 RadioShack 0240 Carver 0157, 0179 Russound 1232, 1233 0531 Classic 1297 Sanyo 0336 Aiwa 1089, 1405, 0158, 1388 0000 Security System 0167...
TECHNICAL SPECIFICATIONS CAA66 Controller/Amplifier Dimensions: 17"W x 11.5"D x 3.9"H (43 x 29.2 x 10 cm) Weight: 17 lbs. 12.5 oz. (8 kg) Power Supply: VAC 100-120 @3A or 220-240V @1.25A 50-60Hz Fuse Rating: 110V input; F3.0A H 250V US and Canada 240V input;...
In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit.