Table of Contents
Advertisement
4-Source Multi-Zone Central
Audio Controller/Amplifiers
CA-Series
Instruction Manual
CA 6.4 6-Zone, 4-Source Central Controller/Amplifier
O
N
O
P
FF
OWER
CA 4.4pi 4-Zone, 4-Source Central Controller/Amplifier
O
N
O
P
FF
OWER
1
2
3
4
5
Z
ONE
1
2
3
4
Z
ONE
ROCK
R&B
JAZZ
CHILDRENS
• ON / OFF
• VOLUME
SOURCE
• SOURCE
REMOTE SENSOR
CA-KP.2
CA-LCD
6
Z
—
4
S
C
C
O N E
O U R C E
E N T R A L
O N T R O L L E R
6
4
Z
—
4
S
C
C
O N E
O U R C E
E N T R A L
O N T R O L L E R
VOLUME
STORE
POWER
REMOTE SENSOR
/ A
M P L I F I E R
CA 6.4
/ A
M P L I F I E R
CA 4.4pi
Advertisement
Table of Contents
Related Manuals for Russound CA-Series
Summary of Contents for Russound CA-Series
- Page 1 4-Source Multi-Zone Central Audio Controller/Amplifiers CA-Series Instruction Manual CA 6.4 6-Zone, 4-Source Central Controller/Amplifier OWER CA 4.4pi 4-Zone, 4-Source Central Controller/Amplifier OWER ROCK JAZZ • ON / OFF • VOLUME • SOURCE REMOTE SENSOR CA-KP.2 — O N E —...
- Page 2 50Hz operation please select the power cord for your area. Select the plug for your area at one end and a IEC320 connector at the other. It is not necessary to make any other changes. If you have any questions please call Russound Inc. 1800-638-8055 or 603-659-5170 Safety Instructions: 1.
-
Page 3: Table Of Contents
Product Overview ....... .4 Possible System Configurations .....4 Unpacking and Warranty Card . -
Page 4: Product Overview
High-current, stereo, power amplifiers are built into the Russound CA allowing simple connections to each speaker in the system. Each zone is operated by an intuitive, easy-to-use keypad that controls all the functions of the CA. The keypads also have a built-in infrared receiv- er that allows remote commands for your source equipment to be routed through the CA. -
Page 5: Getting Started
CAT-5). This wire will be used to connect the keypads in each zone to the controller. 16 Gauge minimum, 2 conductor CL3 rated wire. (Russound AW162CL3) This wire is used for direct connection between the CA and your speakers. -
Page 6: Rear Panel Connections
(Color) Left + _______________ Left - _______________ List 3 – Room names should be written below Zone 1 ________________ Zone 2 ________________ Zone 3 ________________ Zone 4 ________________ VOLTAGE SELECTOR DESIGNED BY RUSSOUND MADE IN KOREA ~220-240VAC – ARNING HOCK... -
Page 7: Zone Pre-Amp Outputs
ZONE PRE-AMP OUTPUTS (CA4.4PI ONLY) In applications where more power than the 20 watts per channel is desired, connect one or more zones of the CA4.4pi to an external amplifier. Using standard RCA connectors, wire from the pre-amp outputs of the CA4.4pi to the ampli- fier's inputs. -
Page 8: Keypad Connections At Controller
EYPAD ONNECTIONS • Each keypad connection on the back panel of the CA-Series Master Controller corresponds to the room / zone number chosen for your speakers. Each zone operates independently, so it is very important to connect the keypad to the correct zone keypad input. -
Page 9: Installing Keypads
PUNCHDOWN TERMINALS Figure 11 – Punchdown Terminal on CA-KP.2 and CA-LCD The CA-KP.2 and CA-LCD come with 110 punchdown termi- nals. These terminals are quick, easy to install and provide a strong connection. Punchdown terminals require the use of a punchdown tool. -
Page 10: Setting The Keypads
+, - terminals of the CA-LCD to the SRM-2.1 +, - terminals. Figure 15 – SRM-2.1 connection to CA-LCD CA-KP.2 AMPLIFIED ZONE INPUT FROM RUSSOUND MULTI-ZONE SYSTEM Refer to the SRM-2.1 Instruction Manual for complete wiring directions. ENTER... -
Page 11: Speaker Installation
PEAKER NSTALLATION SPEAKER INSTALLATION • If you are installing in-wall speakers, follow the instruc- tions provided with your speakers for mounting. • Connect each speaker wire to the correct polarity (+,-). Figure 16 - Wire Polarity FINALLY!!! • Make sure that the voltage selector, located on the rear panel of the CA, is on the correct current for your country, either 110V or 220V •... -
Page 12: Operation
PERATION OPERATING THE MAIN UNIT • Power switch: When the power switch is engaged, the CA power indicator will be lit an amber color. The CA should be left on at all times. The unit will consume very little power unless the zones are on and active. -
Page 13: Operating The Ca-Lcd Keypad
OPERATING THE CA-LCD KEYPAD 1) Display: The LCD panel displays the name of the source selected and the volume level. 2) Source: The source button is pressed to select one of the four sources to listen to. Press the source button until the desired source is selected. -
Page 14: Specifications
Please take the following steps to troubleshoot the system. 1) Turn off the power switch on the front of the CA-Series controller. 2) Disconnect all keypad connections from the rear of the controller. -
Page 15: Warranty
In these cases the repair will be made at the owners expense. To return for repairs, the unit must be shipped to Russound at the owners expense, along with a note explaining the nature of the service required. Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. - Page 16 D I S T R I B U T I O N & C O N T R O L S Y S T E M S 5 Forbes Rd. Newmarket, NH 03857 ☎ 603.659.5170 • Fax 603.659.5388 e-mail: tech@russound.com Fax-On-Demand: 603.659.5590 Come visit us at: 28-1116 R6...