Page 1
T 1 / E 1 A S A P A D A P T E R C A R D I N S T A L L A T I O N G U I D E Alcatel-Lucent Proprietary This document contains proprietary information of Alcatel-Lucent and is not to be disclosed or used except in accordance with applicable agreements.
Page 2
The customer hereby agrees that the use, sale, license or other distribution of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the use, sale, license or other distribution of the products in such applications.
Page 6
List of Tables Page 6 7705 SAR T1/E1 ASAP Adapter Card Installation Guide...
Page 7
Figure 6: Installing a 16-port T1/E1 ASAP Adapter Card in a 7705 SAR-8 ......24 Figure 7: Installing a 32-port T1/E1 ASAP Adapter Card in a 7705 SAR-18 .
Page 8
List of Figures Page 8 7705 SAR T1/E1 ASAP Adapter Card Installation Guide...
(CFR) Part 68, Subpart F. Failure to comply will result in damage to the jack. T1/E1 ASAP Card Versions The 7705 SAR-8 and 7705 SAR-18 support the 16-port T1/E1 ASAP Adapter card version 1 (a16-chds1) and version 2 (a16-chds1v2), and the 32-port T1/E1 ASAP Adapter card version 2 (a32-chds1v2).
Page 10
Preface List of Technical Publications The 7705 SAR OS documentation set is composed of the following guides: • 7705 SAR OS Basic System Configuration Guide This guide describes basic system configurations and operations. • 7705 SAR OS System Management Guide This guide describes system security and access configurations as well as event logging and accounting logs.
Page 11
Class 1 laser products are listed in the Class 1 laser adapter card documents. Only approved Class 1 replaceable laser transceivers should be used with those Class 1 Laser Product products. 7705 SAR T1/E1 ASAP Adapter Card Installation Guide Page 11...
Page 12
Step 8. Technical Support If you purchased a service agreement for your 7705 SAR and related products from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance. If you purchased an Alcatel-Lucent service agreement, check this link for instructions to contact Support personnel: Web: http://support.alcatel-lucent.com...
Installing Adapter Cards In This Chapter This chapter provides information about installing and removing the 16-port T1/E1 ASAP Adapter card and 32-port T1/E1 ASAP Adapter card on the 7705 SAR-8 and 7705 SAR-18 chassis: • Power Consumption on page 14 •...
24 W 30 W version 2 (a32-chds1v2) Refer to “Power Consumption” in the 7705 SAR-8 Installation Guide or 7705 SAR-18 Installation Guide for more information on the power consumption of other hardware. Page 14 7705 SAR T1/E1 ASAP Adapter Card Installation Guide...
Installing Adapter Cards Provisioning Requirements To configure cards and ports, you must be able to access the 7705 SAR-8 or 7705 SAR-18 by console or Telnet connection. Refer to the 7705 SAR-8 Installation Guide or 7705 SAR-18 Installation Guide for information and instructions on console and Telnet connections.
Within this maximum, up to 6 16-port T1/E1 ASAP Adapter cards and/or 32-port T1/E1 ASAP Adapter cards can be configured on a 7705 SAR-8, and up to 12 16-port T1/E1 ASAP Adapter cards and/or 32-port T1/E1 ASAP Adapter cards can be configured on a 7705 SAR-18.
Page 18
Installing Adapter Cards Use the config>show card state command to display administrative and operational states for all provisioned cards on a 7705 SAR-8: ALU-1>config# show card state =============================================================================== Card State =============================================================================== Slot/ Provisioned Equipped Admin Operational Num Comments Type Type...
If you will be replacing it with a card of the same type, you do not need to remove the associated configuration. Refer to the 7705 SAR OS Interface Configuration Guide for details on configuring cards and ports.
Adjust LBO settings appropriately so that the T1/E1 ASAP Adapter card receiver’s nominal input voltage level is < 3Vp. Refer to “Configuring DS1 Line Buildout” in the 7705 SAR OS Interface Configuration Guide for detailed information on attenuating transmit signals.