Volume Punch-Through; Channel Control Punch-Through - Harman Kardon AVR 520 Owner's Manual

Programming the Remote
Notes on Using the AVR 520 Remote
With Other Devices.
• Manufacturers may use different code sets
for the same product category. For that rea-
son, it is important that you check to see
whether the code set you have entered oper-
ates as many controls as possible. If it
appears that only a few functions operate,
check to see whether another code set will
work with more buttons.
• When a button is pressed on the AVR 520
remote, the red light under the Input
Selector e for the product being operat-
ed should flash briefly. If the Device Control
Selector flashes for some but not all buttons
for a particular product, it does NOT indicate
a problem with the remote but rather that
no function is programmed for the button
being pushed.

Volume Punch-Through

The AVR 520's remote may be programmed to
operate the Volume Control 40
43 functions of either the TV or the AVR 520
in conjunction with any of the devices con-
trolled by the remote. For example, since the
AVR 520 will likely be used as the sound sys-
tem for TV viewing, you may wish to have the
AVR 520's volume activated, although the
remote is set to run the TV. Either the AVR 520
or TV volume control may be associated with
any of the remote's devices. To program the
remote for Volume Punch-Through, follow these
steps:
1. Press the Input Selector e for the unit
you wish to have associated with the volume
control and the Mute Button 43
same time until the red light appears under
the Input Selector e and note that the
Program/SPL Indicator c will flash
amber.
2. Press the Volume Up Button
note that the Program/SPL Indicator c
will stop flashing and stay amber.
3. Press either the AVR Selector f or the
Input Selector e, depending on which
system's volume control you wish to have
attached for the punch-through mode. The
Program/SPL Indicator c will blink
green three times and then go out to confirm
the data entry.
40 PROGRAMMING THE REMOTE
Example: To have the AVR 520's volume
control activated even though the remote is
set to control the TV, first press the
Video/TV Input Selector e and the
Mute Button
press the Volume Up Button
lowed by the AVR Selector f.
NOTE: Should you wish to return the remote to
the original configuration after entering a
Volume Punch-Through, you will need to repeat
the steps shown above. However, press the same
Input Selector in Steps 1 and 3.

Channel Control Punch-Through

The AVR 520's remote may be programmed to
operate so that the channel control function for
either the TV, cable or satellite receiver used in
your system may be used in conjunction with
one of the other devices controlled by the
remote. For example, while using and controlling
the VCR, you may wish to change channels on a
cable box or satellite receiver without having to
and Mute change the device selected by the AVR 520 or
the remote. To program the remote for Channel
Control Punch-Through, follow these steps:
1. Press the Input Selector Button e for
the device you wish to have the channel con-
trol associated with and the Mute Button
43 at the same time until the red light
appears under the Input Selector e and
the Program/ SPL Indicator c flashes
amber.
2. Press the Volume Down Button
Program/SPL Indicator c will stop flash-
ing and stay amber.
at the
3. Press and release the Input Selector
Button e for the device that will be used
to change the channels. The Program/SPL
Indicator c will blink green three times
and then go out to confirm the data entry.
40 and
Example: To control the channels using your
Cable Box or Satellite Receiver while the
remote is set to control the VCR, first press
the VID 1/VCR Input Selector Button e
and the Mute Button
time. Next, release them and press the
Volume Down Button
VID 2/TV Input Selector Button e.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original
configuration, repeat the steps shown in the
example above. However, press the VID 1/VCR
Input Selector in Steps 1 and 3.
Transport Control Punch-Through
43
at the same time. Next, The AVR 520's remote may be programmed to
40 , fol- operate so that the Transport Control
Functions z (Play, Stop, Fast Forward,
Rewind, Pause and Record) for a VCR, DVD or
CD will operate in conjunction with one of the
other devices controlled by the remote. For
example, while using and controlling the TV, you
may wish to start or stop your VCR or DVD with-
out having to change the device selected by the
AVR 520 or the remote. To program the remote
for Transport Control Punch-Through, follow
these steps:
1. Press the Input Selector e for the device
2. Press the Play Button z. The Program/
3. Press and release the Input Selector
. The
40
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original
configuration, repeat the steps shown in the
example above. However, press the VID 2/TV
Input Selector in Steps 1 and 3.
NOTE: Before programming the remote for
at the same Volume, Channel or Transport Punch-Through,
43
make certain that any programming needed for
40
, followed by the the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.
you wish to have the channel control associ-
ated with and the Mute Button
43
same time until the red light appears under
the Input Selector e and the Program/
SPL Indicator c flashes amber.
SPL Indicator c will stop flashing and
stay amber.
Button e for the device that will be used
to change the channels. The Program/SPL
Indicator c will blink green three times
and then go out to confirm the data entry.
Example: To control the transport of a DVD
player while the remote is set to control the
TV, first press the VID 2/TV Input Selector
Button eand the Mute Button
the same time. Next, release them and press
the Play Button z, followed by the DVD
Input Selector Button e.
at the
43 at