Table of Contents
Advertisement
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, do not
let bare skin touch hot surfaces. If provided, use handles
when moving this appliance. Keep combustible materials,
such as furniture, pillows, bedding, papers, clothes and cur-
tains at least 3 feet (914mm) from the front of this appli-
ance.
3. CAUTION: Extreme caution is necessary when any
heater is used by or near children or invalids and when-
ever the heater is left operating unattended.
4. If possible always unplug this appliance when not in use.
5. Do not operate any heater with a damaged cord or plug or
after the appliance malfunctions, has been dropped or dam-
aged in any manner.
6. Any repairs to this appliance should be carried out by a
qualified service person.
7. Under no circumstances should this appliance be modified.
Parts having to be removed for servicing must be replaced
prior to operating this stove again.
8. Do not use outdoors.
9. This heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. Never locate this appli-
ance where it may fall into a bathtub or other water contain-
er.
10.Do not run cord under carpeting. Do not cover cord with
throw rugs, runners or the like. Arrange cord away from
traffic areas and where it will not be tripped over.
11.To disconnect this appliance, turn controls to the off posi-
tion, then remove plug from outlet.
12.Connect to properly grounded outlets only.
13.This appliance, when installed must be electrically grounded
in accordance with local codes, with the current CSA C22.1
Canadian Electrical codes or for USA installations, follow
local codes and the National Electric Code, ANSI/NFPA No.
70.
14.Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock,
fire or damage the appliance.
15.To prevent possible fire, do not block air intakes or exhaust
in any manner. Do not use on soft surfaces, like a bed,
where openings may become blocked.
16.This appliance has hot and arcing or sparking parts inside.
Do not use it in areas where gasoline, paint or flammable
liquids are used or stored. This appliance should not be
used as a drying rack for clothing, nor should Christmas
stockings or decorations be hung on or near it.
17.Use this appliance only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electric shock or injury to persons.
18.Avoid the use of an extension cord because of the risk of
overheating the cord and the risk of fire. Extension cords
are for temporary use only. If an extension cord must be
used, it must be UL/CSA certified, rated at 15A (1875W),
10009285
Installation Instructions
General
SAVE THESE INSTRUCTIONS
125V maximum with 14 AWG minimum and constructed of
two current carrying conductors with ground. A heavy duty
extension cord with the shortest length possible for the
connection is recommended and must not be longer than
50 ft. (15.2 m). Do not coil or cover the extension cord.
Locating Your Fireplace
Your new fireplace may be installed in a prefabricated
cabinet available from your dealer.
When choosing a location for your new fireplace, ensure
the general instructions are followed. Also, for best effect
install the fireplace out of direct sunlight.
Clearance to Combustibles
Sides . . . . . . . . . . . . . . . . . . . 0" (0 mm)
Floor . . . . . . . . . . . . . . . . . . . .0" (0 mm)
Top . . . . . . . . . . . . . . . . . . . . .0" (0 mm)
Cabinet Installations
Cabinets are available from your dealer which allow for fast,
convenient installation of your fireplace against existing walls.
For instructions on handling and assembly of your cabinet,
refer to separate installation instructions that come with the
cabinet.
If it is necessary to secure your fireplace into a cabinet or wall
opening, the following instructions apply (hardware not sup-
plied).
Remove the glass door from the unit and set aside. 3/16" (5
mm) clearance holes, two (2) per side must be drilled through
the fireplace sides for #8 x 3/4" long black oxide wood screws
or similar. The mounting holes can be located on left and right
sides approximately 2" (51 mm) from the top and 5" (127 mm)
from the bottom of the glass door area. The mounting hole
location distance from the front of the unit must not interfere
with the glass door and the refractory (brick pattern) when rein-
stalled. If necessary, modify the cabinet or wall opening for the
mounting screws to attach. Double check the mounting hole's
locations on the fireplace before drilling. A small 1/16" (2 mm)
pilot hole or center punch before drilling is recommended.
Mark and drill from the outside to avoid marking or damaging
the interior of the fireplace. Tighten the screws evenly so the
unit remains centered in the opening and without distorting the
sides of the fireplace unit. It is advisable to place wood shims
or similar between the fireplace sides and the cabinet to pre-
vent distortion when tightening the screws. 1/2" (13 mm)
Velcro strips for securing the log to the grate tines and away
from the screen are recommended.
3
Hide quick links:
Advertisement
Table of Contents
