Table of Contents
Advertisement
Info - General - Prod menu shows:
The
Total running : The total hours the product has used
•
the wheel motors (cutting and searching).
•
Mower s/n : The product's serial number. This
number must correspond with the serial number on
the inside of the hatch.
Prod. date : The product's date of manufacture.
•
MCB s/n : The main circuit board's serial number.
•
This is not linked to the product's serial number.
MCB prod : The main circuit board's date of
•
manufacture.
COM s/n : The communication board's serial number.
•
This is not linked to the product's serial number.
4.3.1.2 Tools - Info - Battery
The
Tools - Info - Battery menu shows:
Voltage : The battery's voltage level. About 20.5 V
•
indicates a fully charged battery and about 17 V
indicates a flat battery.
Charges : The accumulated number of charge cycles
•
since date of manufacture, or since the counter was
reset.
Charge level : Shows the state of charge for the
•
battery. When the battery is fully charged, the
charge is approximately 1 700 mAh. When the
charge has dropped to approximately 1 000 mAh the
product returns to the charging station.
Current : Shows nominal regulated charge current
•
to and from the battery. A positive value indicates
that the battery is charging and a negative value
indicates that the product is using current from the
battery.
Temp : Shows current temperature in the battery.
•
Capacity : Shows the maximum capacity for the
•
battery.
4.3.1.3 Tools - Info - Loop
Tools - Info - Loop menu has 3 sections:
The
A-loop shows the loop signal from the boundary
•
loop measured by the loop sensors in the product.
The value should lie between approximately 40 and
320 to ensure good functionality. The closer to the
loop the product is, the higher the value. When the
product is directly over the loop, the value is 0 and
when the product is outside of the loop, the value is
negative.
G/F shows the loop signals from the Guide and the
•
field for F. To ensure good functionality, the value for
the Guide signal should be (-) 70-120 beside each
guide wire.
Quality shows the loop system's signal quality. The
•
loop signals can only be correct interpreted if the
value is 100%. If the value is lower, the loop system
does not function correctly and thus none of the
displayed signals are correct.
4.3.1.4 Tools - Info - Sensors
Tools - Info - Sensors menu has 2 sections:
The
1413 - 003 - 17.01.2022
Status
•
Temperature
•
Info - Sensors - Status menu shows:
The
•
Lifted : When the body is lifted up the lift sensor is
activated and the product display shows
Tilted : When the product is standing horizontally the
•
value should be max ±3. Inclination up and to the left
is shown as negative values.
Normal position : Yes indicates that the product is
•
standing in a normal position and
the product is upside down.
The Info - Sensors - Temperature menu shows:
Product temperature : Measured by a temperature
•
sensor on the main circuit board.
LCD temperature : Measured by a temperature
•
sensor on the HMI circuit board.
4.3.1.5 Tools - Info - Motors
Tools - Info - Motors menu has 2 sections:
The
Wheel motor
•
Cutting motor
•
Info - Motors - Wheel motor menu shows:
The
Speed for the left/right wheel motor.
•
Current (mA) for the left/right wheel motor.
•
Power (%) for the left/right wheel motor.
•
Info - Motors - Cutting motor menu shows:
The
Speed of the cutting motor.
•
Current (mA) for the cutting motor.
•
Average current (mA) for the cutting motor.
•
4.3.2 Tools - History, total
4.3.2.1 Tools - History, total - Key data
The Tools - History, total - Key data menu shows:
Total running : The total time in hours that the wheel
•
motors have been running.
Total running also includes the time when the
Note:
product is running without mowing.
Total mowing : The total time in hours that the
•
cutting motor has been running.
Total search time : The total time in hours that the
•
product has been in search mode. This means the
time from starting to search for the charging station,
until the product has docked. Depending on the
installation and work area, it is normal with 10-20%
search time of the total running time.
Total charge time : The total time in hours when the
•
product has been charging.
Complete chargings : The total number of complete
•
chargings. A complete charging is defined as a
charging that proceeds for more than 20 minutes,
and is terminated when the charge current is less
than 300 mA.
Yes .
No indicates that
Special menus - 9
Advertisement
Table of Contents
