Settings For The Entire Unit; Returning To The Factory Settings; (Factory Reset); Saving The System Settings - Roland JUPITER-X Owner's Manual

Settings for the Entire Unit

Returning to the Factory Settings

(Factory Reset)

Here's how the settings that you edited and saved on the JUPITER-X
can be returned to their factory-set condition.
* When you execute this operation, all saved settings including the sound
parameters will be lost.
* If you will later need the current settings, be sure to use the backup
function (p. 24) to save the current settings before you restore the
factory settings.
1.
Press the [MENU] button.
2.
Use the [1] knob to select "UTILITY", and then press the
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select
the [ENTER] button.
The FACTORY RESET screen appears.
If a sound pack or wave expansion is installed or
imported
If a sound pack or wave expansion is not installed or
imported
4.
Use the PAGE [ ] buttons
] [
and press the [ENTER] button
Press [ENTER] again to clear the check box.
Item Explanation
Initializes the scenes and user tones (* 1).
Reset User Data
Initializes the system settings (* 1).
Reset System Data
Initializes the user license and wave expansion. Initializing
the user license lets you import/install a sound pack or
Remove License
wave expansion that was downloaded with a different
(*2)
user license.
* This deletes the currently installed wave expansion.
* 1 Performing these operations erases any of the relevant data you have
edited after purchase.
To save the current settings, be sure to use the backup function (p.
24) before you restore the unit to its factory settings.
* 2 This is displayed if a sound pack or wave expansion is installed.
For more details on user licenses, see the
Installation Manual" (PDF).
5.
Press the cursor [>] button.
A confirmation message appears.
If you decide to cancel, press the
PAGE [ ] [ ] buttons
"FACTORY RESET", and then press
to select the item to execute,
to select its check box.
"Sound Pack/Wave Expansion
[EXIT] button.
6.
To execute, use the [2] knob
the [ENTER] button.
The display indicates "Completed. Turn off
7.
Turn the power of the JUPITER-X off and then on again.
* Never turn off the power or disconnect the USB flash drive during a
process, such as while the "Executing..."

Saving the System Settings

1.
Press the [MENU] button.
2.
Use the [1] knob to select "SYSTEM", and then press the
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select the parameter and use the
knob to change the setting.
Saving the System Settings
1.
In the system setting screen, press the
A confirmation message appears.
If you decide to cancel, press the
2.
To execute, press the [ENTER]
System parameter list
Parameter Value
[1] knob [2] knob
SYSTEM - GENERAL
AGING
Specifies whether the character of the sound (pitch variance)
changes according to the varying internal temperature of this
unit.
This has an effect only on analog synthesizer models.
The internal temperature value is shown in the upper right of the
top screen of the scene.
OFF
ON
Warm-up
FAST
FIXED
Specifies the initial internal temperature for Warm-up.
REAL
Init Temp
0–60°C/32–140°F
to select "OK", and then press
power".
display is shown.

(System)

PAGE [ ] [ ] buttons
(System Write)
[WRITE] button.
[EXIT] button.
button.
Explanation
The character of the sound is not affected by
the temperature. Nor is there a temperature
indication in the SCENE screen.
The internal temperature starts at the value
specified by Aging Init Temp, and changes to
the actual temperature (REAL).
Although it depends on the temperature
difference, the REAL temperature is reached
in approximately ten minutes. After reaching
the REAL temperature, the setting follows the
actual temperature change.
The internal temperature starts at the value
specified by Aging Init Temp, and then
quickly (in approximately ten seconds)
changes to the actual temperature (REAL)
when you play the keyboard. After reaching
the REAL temperature, the setting follows the
actual temperature change.
The internal temperature is fixed at the
value specified by Aging Init Temp, and the
character of the sound is maintained at that
point.
The internal temperature that is actually
measured will be the initial temperature.
Virtually specifies an initial internal
temperature (Celsius).
[2]
27