Advertisement
Quick Links
Applied Machine: 950
MFP: 95ppm
Product Code: A0Y5
I. Accessory parts
No.
Name
1. Machine
installation
plate/lower
2. Machine
installation
plate/upper
3. Paper exit
up-down tray
4. Paper exit
tray /1
5. Knob screw
6. TP screw
M4x6
7. TP screw
M4x14
8. Truss screw
M4x8
9. Fixing material
10. Installation
manual
Note:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take a
good position of not being excessively loaded.
(mass: approx. 65kg)
FS-528
INSTALLATION MANUAL
Shape
Q'ty
1
15JMIXC001SA
1
15JMIXC002SA
1
15JMIXC003SA
1
15JMIXC004SA
2
2
2
2
1
15JMIXC005SA
1
Finisher
II. Confirmation before installation
Note:
1. When transporting the Finisher, be sure to move
it in the direction illustrated below so as not to
deform the casters on the paper exit tray side.
2. Choose a horizontal and stable floor for installing
the machine.
3. When installing optional Post Inserter/Punch kit
to the Finisher, be sure to install it beforehand,
then install the finisher to the copier machine.
III. Installation procedure
1. Turn the Sub and Main power switches OFF, and
unplug the power cord from the outlet.
2. Remove the connector cover on the left side
cover of the machine. (1 screw)
E-1
15JKIXC001SA
Connector cover
A10UIXC001CA
A10U955000
Advertisement
Related Manuals for Konica Minolta FS-528
Summary of Contents for Konica Minolta FS-528
- Page 1 FS-528 Finisher INSTALLATION MANUAL Applied Machine: 950 MFP: 95ppm Product Code: A0Y5 I. Accessory parts II. Confirmation before installation Note: Name Shape Q’ty 1. When transporting the Finisher, be sure to move 1. Machine it in the direction illustrated below so as not to installation deform the casters on the paper exit tray side.
- Page 2 3. Install the machine installation plate (lower) on 5. Visually inspect the Finisher. the lower left side of machine. (TP screw M4x6: 2 6. Remove the locking tapes and the locking protec- pcs.) tion materials from the front door and the left side of the Finisher.
- Page 3 9. Remove the screw from the staple waste box. 13. Remove staple-locking material/1 (7 screws). 10. Remove the screw from the locking material at the back of the stacker, and pull out the stacker. staple-locking material/1 Locking material Staple waste box screw 15VFIXE005SA 14.
- Page 4 16. Remove the cushion materials and the locking 17. Remove the two locking materials from inside tape from inside the stacker. the stacker (3 screws each). (1) Remove the two cushion materials in the stapler. Remove the protection sheets (2 areas). Front Rear Protection sheet...
- Page 5 19. Install the staple-locking material/1 which is 22. Install the Finisher on the machine. removed in the step 13 with the removed (1) Fit the hooks on the machine installation plates (upper and lower) into the upper and lower screws. holes on the Finisher as illustrated below, then When installing, attach the fixing material included lock them by pushing the Finisher to the back.
-
Page 6: Confirmation Of Operation
IV. Confirmation of operation (2) Fix the Finisher to the machine. (Knob screw: 2 pcs.) 1. Turn ON the Main and Sub power switches. 2. Execute the printing in the Sort mode to check if it operated correctly. 3. Execute the printing in the Staple mode to check if it stapled correctly.