Table of Contents
Advertisement
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools Needed
Tape measure
■
Phillips screwdriver
■
Flat-blade screwdriver
■
1/8" (3 mm) flat-blade
■
screwdriver
Level
■
Drill
■
Wrench or pliers
■
Pipe wrench
■
15/16" (2.4 cm)
■
combination wrench
1/8" (3.2 mm) drill bit
■
(for wood floors)
Marker or pencil
■
Parts Supplied
Check that all parts are included.
Propane/Natural Gas Conversion Kit
■
#10 x 1
/
" (4.1 cm) screws (for mounting anti-tip bracket) (2)
5
■
8
Anti-tip bracket (inside oven cavity)
■
Anti-tip bracket must be securely mounted to the back wall
or floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
Parts Needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See "Electrical Requirements" and
"Gas Supply Requirements" sections.
IMPORTANT: When the range is used under microwave models:
JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door
Baffle Plate Part Number W10737014 must be ordered and
used. Please reference the "Accessories" section of the User
Guide for contact information.
4
INSTALLATION REQUIREMENTS
Pipe-joint compound
■
resistant to Propane gas
3/16" (4.8 mm)
■
carbide-tipped masonry
drill bit (for concrete/
ceramic floors)
Noncorrosive leak-
■
detection solution
For Propane/Natural Gas
Conversions
5/8" (1.6 cm) combination
■
wrench
3/8" (1 cm) nut driver
■
9/32" (7 mm) nut driver
■
Masking tape
■
Optional Parts
■
To purchase these or any other accessories, please reference the
"Accessories" section of the User Guide for contact information.
Side Trim Kits:
■
5/8" (1.7 cm) White - Order Part Number W10675027
5/8" (1.7 cm) Black - Order Part Number W10675026
5/8" (1.7 cm) Stainless Steel - Order Part Number
W10675028
1
/
" (2.9 cm) White - Order Part Number W10731885
1
8
1
/
" (2.9 cm) Black - Order Part Number W10731886
1
8
1
/
" (2.9 cm) Stainless Steel - Order Part Number
1
8
W10731887
Backsplash Kits:
■
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number
W10655450
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Do not obstruct flow of combustion and ventilation air.
It is the installer's responsibility to comply with installation
■
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on
the top right-hand side of the oven frame.
The range should be located for convenient use in the
■
kitchen.
Recessed installations must provide complete enclosure of
■
the sides and rear of the range.
All openings in the wall or floor where range is to be installed
■
must be sealed.
Cabinet opening dimensions that are shown must be used.
■
Given dimensions are minimum clearances.
The anti-tip bracket must be installed. To install the anti-tip
■
bracket shipped with the range, see "Install Anti-Tip Bracket"
section.
Grounded electrical supply is required. See "Electrical
■
Requirements" section.
Proper gas supply connection must be available. See "Gas
■
Supply Requirements" section.
Contact a qualified floor covering installer to check that the
■
floor covering can withstand at least 200°F (93°C).
Use an insulated pad or 1/4" (6.4 mm) plywood under range
■
if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
Advertisement
Table of Contents
