Midi - Roland VAD506 Data List

SYSTEM

MIDI

Here you can make settings that specify how MIDI messages are transmitted to or received from a MIDI device connected to this unit.
Parameter
[F1] button (BASIC tab)
MIDI Tx/Rx Sw
MIDI Channel
Program Change Tx
Program Change Rx
Soft Thru MIDI In
Soft Thru USB MIDI In
Local Control
Device ID
Transmit Edit Data
Receive Exclusive
[F2] button (CONTROL tab)
HH Pedal CC
Snare CC
Ride CC
TOMs/AUXs CC
HH Note# Border
Hi-Reso Velocity
Cymbal Choke Shot
[F3] button (SYNC tab)
Sync Mode
Clock Source
Sync Out
38
Value
OFF, ON
1–16Ch
OFF, ON
OFF, ON
This allows performance data from a MIDI device connected to the TD-27's MIDI IN connector to be transmitted to another MIDI device
connected to the MIDI OUT connector or to a computer connected to the USB COMPUTER port.
OFF
ON (MIDI OUT)
ON (USB MIDI)
ON (MIDI+USB)
Performance data from a computer connected to the TD-27's USB COMPUTER port can be transmitted to a MIDI device connected to the
MIDI OUT connector.
OFF
ON (MIDI OUT)
OFF, ON
17–32
OFF, ON
OFF, ON
OFF, 1, 2, 4, 11, 16, 17, 18, 19
0–127
OFF, ON
OFF, ON
Specifies the synchronization signal according to which the TD-27 operates.
INTERNAL
EXTERNAL
MIDI, USB MIDI
OFF, ON
Explanation
Turns the transmitting and receiving MIDI messages on/off.
Transmit and receive channel.
Turns program change transmission on/off
Turns program change reception on/off
Performance data received from the TD-27's MIDI IN connector will not be sent to the MIDI OUT
connector or the USB COMPUTER port.
Performance data received from the TD-27's MIDI IN connector will be sent to the MIDI OUT
connector.
Performance data received from the device connected to the TD-27's MIDI IN connector will be sent
to the USB COMPUTER port.
Performance data received from the device connected to the TD-27's MIDI IN connector will be sent
to the MIDI OUT connector and the USB COMPUTER port.
Performance data received via the TD-27's USB COMPUTER port is not transmitted to the MIDI OUT
connector.
Performance data received via the TD-27's USB COMPUTER port is transmitted to the MIDI OUT
connector.
Turns on/off the connection between the performance data from the pads and the TD-27's sound
generator section
Normally you'll leave this "ON. " If this is "OFF, " the performance data from the pads is not connected
to the TD-27's sound generator section.
Device ID setting
The setting described here is necessary only when you wish to transmit separate data to two or
more TD-27 units at the same time. Do not change this setting in any other case.
Specifies whether changes in the TD-27's settings are transmitted as system exclusive messages
(ON) or not transmitted (OFF).
Specifies whether system exclusive messages are received (ON) or not received (OFF).
Control change used for transmitting/receiving the depth to which the hi-hat pedal pressed
Control change used for transmitting/receiving the strike position of the snare
Control change used for transmitting/receiving the strike position of the ride
Control change used for transmitting/receiving the strike position of the tom 1–3 and AUX 1–3
This number specifies the pedal position at which to switch from open hi-hat to closed hi-hat.
* There's no need to change this setting if you're performing and recording only with the TD-27
and the pads.
Disables CC#88 (high resolution velocity prefix).
If this is disabled, the maximum velocity handled by the TD-27 is limited to 127. Velocity is also
limited to 127 for strikes on digitally-connected pads and for input via the MIDI IN connector.
Switches support for the performance technique of striking a pad while choking it.
If this is "ON, " striking a pad while choking it immediately mutes the sound after it begins. If this is
"OFF, " the sound is not muted immediately even if you strike a pad while choking it.
Choose this setting if you're using the TD-27 by itself without synchronizing it to another device, or
if you want another device to operate in synchronization with the TD-27.
The TD-27 operates as a slave device. Choose this setting if you want the TD-27 to operate
according to synchronization messages that it receives from another device.
When Sync Mode is "EXTERNAL, " this specifies whether the TD-27 synchronizes to synchronization
messages from the MIDI IN connector (MIDI) or to synchronization messages from the USB
COMPUTER port (USB MIDI).
Specifies whether MIDI synchronization messages are transmitted to another device (ON) or not
transmitted (OFF).