Table of Contents
Advertisement
NOTE
If the [IP Enable] is set to [ON], you cannot set the [Device-
PTZ], [Record-Normal], [Record-Sensor], [Record-Motion],
[Record-Text], [Record-Instant/Panic] and [Event-Motion]
options because they are deactivated.
IP Camera
•
Channel: Selects the desired channel to set the connected IP
camera.
•
Vendor: Selects the IP camera vendor from the drop-down list.
•
Model Name: Enter the model name of the IP camera.
NOTE
This option is not supported for models LRH7160D and LRH7080D.
•
Stream : Select the camera stream you want to display using the
Stream drop-down box.
•
Host Name: Enter the IP address of the IP camera.
•
User Name: Enter the user ID.
•
Password: Enter the user password.
•
RTSP/HTTP Port: Enter the RTSP/HTTP port number.
ATM/POS Setting
•
Interface Device: Select the interface device from the drop-
down list.
•
Camera: Select the camera number for mapping with ATM/POS
device.
•
Baud Rate: Select the desired parameter to set the
communication speed between DVR and ATM/POS device.
•
Data Bits: Select the number of the data bits for RS-485
communication.
•
Stop Bits: Select the desired parameter. The stop bit is added to
the last of data, in asynchronous communication.
•
Parity: Select the desired parameter. The parity bit is added to
the data, to perform parity check.
Storage
•
Overwrite:
-
On : Overwrite recording is possible when the partition of
HDD have fully recorded.
-
Off: Do not use overwriting.
•
Full Warning: When the HDD has overflowed a warning message
is displayed.
•
Auto Delete: Set the auto delete date. If you set the auto delete
date, the recorded data will be deleted except the data within
the selected date period of time. The Auto Delete function is
activated every 35 minutes.
•
Storage Saving : Saves the storage space by reducing the quality
of the recorded data.
Display settings
•
Channel: Selects the desired channel to adjust.
Channel Composition
•
Name: Selects the desired channel.
NOTE
This option is not supported for models LRH7160D and LRH7080D.
PTZ
Settings for the PTZ cameras connected via the data port of the
RS-485 terminal.
•
Port: Selects the connected data port of the RS-485 terminal
on the rear panel. The DATA 2 port is used to control the PTZ
camera connected to DVR or to control by using the LKD1000
controller. If you want to use the PTZ camera via DATA 2 port,
you should set the [Remote Controller ID] to [NONE]. If you use
the LKD1000 controller to control the DVR via DATA 2 port, you
should set the [Remote Controller ID] number between 1 and
16.
•
Control ID: Selects the PTZ camera ID. Make the same settings
as the PTZ camera.
•
Protocol: Selects the protocol supported by PTZ camera.
•
Baud Rate: Selects the communication speed.
Video Adjustment
Adjust the brightness, contrast and color settings of each camera
channel. You can see the settings screen from the preview windows.
•
Brightness: Adjust the brightness value from 0 to 100 for the
selected channel.
•
Contrast: Adjust the contrast value from 0 to 100 for the selected
channel.c
•
Color: Adjust the color value from 0 to 100 for the selected
channel.
Motion Settings
•
Sensitivity: Set the sensitivity level for the created motion
detection area.
•
Relay Output: Select the number of the RELAY-OUT terminal for
the output alarm (relay) signal when motion is detected.
•
Area: The factory default of the Motion detection area is set as
the whole area. You can change the area by using mouse on the
preview window screen.
-
Select All: Click one point with the left mouse button and
drag & drop to the end point.
-
Clear All : Click the start point with the right mouse button
and drag & drop to the end point.
LG Network Client Program
61
5
Advertisement
Table of Contents
