Table of Contents
Advertisement
PROGRAMMING
NOTICE: If this Security ✚
®
the garage door opener, which provides security against code-theft devices, will be circumvented. The owner of the copyright in the
garage door opener does not authorize the purchaser or supplier of the non-rolling code transmitter to circumvent that technical measure.
The 300 Series remote control works only with door openers and
light controls having a purple "Learn" button.
Programming instructions are described and illustrated below.
The additional push buttons can also activate other garage door
openers and/or light controls. (Instructions for programming light
products are included with those accessories.)
Instructions are Described and Illustrated Below
1.
Press and release the "learn" button on
the motor unit. The learn indicator light
will glow steadily for 30 seconds.
2.
Within 30 seconds, press and hold the
button on the hand-held remote.
3.
Release the button when the motor unit
light blinks. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and the hold "learn" button on motor unit until the learn
indicator light goes out (approximately 6 seconds). All previous
codes are now erased. Reprogram each remote or keyless entry
you wish to use.
To Control the Opener Lights
®
With Security✚
transmitters, a remote push button can be
programmed to operate the opener lights without opening the
door.
1.
With the door closed, press and hold the remote button that
you want to control the light.
2.
Press and hold the Light button on the door control.
3.
Press and hold the Lock button on the door control.
4.
After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights should
turn on or off but the door should not move.
garage door opener is operated with a non-rolling code transmitter, the technical measure in the receiver of
Security ✚
®
3-Button Remote Control Programming (Optional)
1
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
•
ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
•
Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
•
ALWAYS keep gate or garage door in sight until completely
1
2
3
9
1
9
1
7
3
7
3
5
5
KG
KG
closed. NEVER permit anyone to cross path of moving gate
or door.
2
Open/Close/Stop Operation
Your Security✚
programmed to operate one door using all
3 buttons: the large button will only open
the door, the middle button will close the
door and third button will stop the door's
movement. You may set up this feature as follows:
2
1.
With the door closed, press and hold the large remote push
button.
2.
Press and hold the Lock button on the door control.
KG
KG
3.
Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by pressing
the large (Open) button on the remote. The door should open.
Press it again while the door is open and nothing should happen.
Press the middle (Close ) button and the door should close. Press
the third (Stop) button while the door is moving and it should stop
immediately.
Remote Control Batteries
To prevent possible SERIOUS INJURY or DEATH:
•
NEVER allow small children near batteries.
•
If battery is swallowed, immediately notify doctor.
The lithium batteries should
produce power for up to 5 years. To
replace, pry open case with visor
clip or screwdriver, as shown. Insert
batteries positive side up (+).
Dispose of old batteries properly.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
26
®
remote control can be
Open
Close
Stop
Battery
positive
side up (+)
Hide quick links:
Advertisement
Table of Contents
