Rules For Safe Driving; Assistance Service - Peg-Perego IGOD0502 Use And Care Manual

buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated
to the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all studs/nuts of the wheels are secure.
• When operating in overload conditions, such as
soft deep sand, mud or rough uneven terrain, the
overload circuit breaker will automatically
disconnect the power, and you will hear an
INTERMITTENT BEEP for 30 sec. at the end of
which the toy will resume the power delivery and
the vehicle will be operational again.
• You must remove foot from gas pedal to apply the
breaks.
MEANING of BEEPING SOUNDS
• ONE SINGLE BEEP means that the toy is ready to
operate.
• CONTINUOUS BEEP for 10 sec. Means that the
battery is fully discharged and the toy cannot
operate anymore, recharge the battery or change it
with a charged one.
• INTERMITTENT BEEP for 30 sec. means the
motors are hot. The toy will be stopped for at least
30 sec. until the motors cool down.
• Overheat condition can be reached playing longer
on some of these condition:
1 - Too much weight transported
2 - Too steep of incline to climb
3 - High grass driving into
4 - Too soft terrain (mud or sand)
5 - Irregular surface to drive on like rough uneven
terrain, stones, roots
6 - Some combination of these
UNINTERRUPTED FUN: Keep a spare set of
charged batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• When operating in overload conditions, such as
running the vehicle against a fixed object, through
soft deep sand or mud, or over rough or uneven
terrain, the overload circuit breaker will
automatically disconnect the power. After 30 or
more seconds, the circuit breaker will automatically
reset, however-you must eliminate overload
conditions to resume normal driving.
• Press the accelerator pedal to activate the vehicle,
followed by a single BEEP that indicates the toy is
ready to operate.
• If you let the vehicle idle for more than 10 minutes
must repeat the activation process, simply by
pressing the pedal waiting for the BEEP.
• If the vehicle emits a CONTINUOUS BEEP must
recharge the battery.
• If no initial beep is heard, the battery is down and
must be charged.
• If the problem persists after recharging, to check
the battery and the charger to a service center.
• Check that all plugs are properly connected.
• Check electrical switches. Replace if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 •Place from bumper on body and tighten four
screws as shown in the drawing.
2 • Place rear bumper on body.
3 • Tighten three screws as shown in the drawing.
4 • Assemble the two parts of the steering wheel.
5 • Place the horn in the steering wheel's central
hole, following the instructions in its packaging.
6 • Insert the steering wheel on the steering wheel
column.
7 • Align steering wheel column holes with steering
wheel: nut fits into haxagon hole, bolt into round
hole.
8 • Insert the windscreen.
9 • Secure it by means of the two screws.
10 • Fit the removable seat cover as shown in the
figure.
11 • Hook the front elastic bands.
12 • Position the other two elastic bands.
13 • Place seat on body. Adjust seat position. Secure it
with washer and thumb nut.
14 • Join A to part B of the Roll-Bar.
15 • Join A-B to the upper section of the Roll-Bar C,
insert and rotate to secure.
16 • Insert the 2 plates in the slots at the base of the
Roll-Bar and hold them in place. Secure the
plates and the Roll-Bar with the 2 screws
provided (detail A).
17 • Insert the end of the safety belt in the slot
situated centrally in the bottom of the seat, as
shown in the figure.
18 • Screw the net down to the body.
19 • Snap it around the roll-bar as shown in the
drawing.
20 • Insert the rearview mirrors in the direction
shown by the arrow.
21 • Place the 2 plastic signs, pressing down as you do
so.
22 • Snap fit the four hub covers onto the wheels.
23 • Insert the antenna, pressing down as you do so,
into its appropriate housing, situated on the right
rear mudguard.
24 • Remove the radio from its packaging. Unscrew
the cover from the battery chamber. Insert two
1.5 Volt AA batteries (not supplied with the
vehicle) into the compartment, taking care to
position the positive and negative poles correctly.
Close the battery compartment cover and screw
into place.
25 • Insert the wire from the antenna and the radio
into their appropriate housing on the dashboard,
making sure to place them the right way up, as
shown in the figure.
26/7•Open the hood. Remove the two screws from
the simulated engine. Remove the simulated
engine. Proceed as follows:
- Remove the battery from the packaging;
- unscrew the battery block screw;
- position the battery;
- lock it down using the special battery block.
28 • Plug battery terminal A into vehicle wiring
terminal B.
29 • Lower the imitation motor and screw it down
again. Close the hood, securing it in place with
the 2 hooks. The vehicle is now ready for use.
FEATURES AND INSTRUCTIONS FOR
USE
30 • Hood support shaft.
31 • Below the box you can find four removable toy
tools. To remove the box, pull out and unfasten
the four couplings.
32 • A:HORN. Push the yellow button the horn will
sound.
B: FM RADIO: a real removable car radio that
works independently. Press button 3 to turn it
on. Press button 4 to turn it off. Use the