Flame Led Light And Media Light Assembly Replacement; Top Light Replacement; Flicker Motor & Rod Replacement - Dimplex PF3033 Service Manual

Flame LED Light and Media Light
Assembly Replacement
Tools Required: Phillips Head Screwdriver
Small Adjustable Wrench
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
firebox and the 3 along the middle of the panel (Figure 2).
5. Locate the flame LED light assembly, at the bottom of
the unit. (Figure 2)
6. Locate and remove the two screws on either end secur-
ing the bracket, that the light assembly and the flicker
rod are attached to, and remove assembly (Figure 6).
7. Using the small adjustable wrench remove the 3 nuts
or plastic standoffs, by pressing the center pin out to
release the board, to remove the LED light assembly.
8. Follow the wiring to the main control board and replace
with new connection.
9. Properly orient and insert the new LED light assembly.
10. Reassemble in the reverse order as above.
Figure 6
Mounting Screws
Securing Nuts
Flame LED Light

Top Light Replacement

Tools Required: Phillips Head Screwdriver
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
5. Locate the top light that requires to be replaced. (Fig-
6. Release door that houses the LED light board by press-
7. Release the LED light board from the top panel by us-
8. Follow the wiring to the main control board and replace
9. Properly orient and insert the new board.
10. Reassemble in the reverse order as above.
Flicker Motor & Rod Replacement
Tools Required: Phillips Head Screwdriver
at least 10 minutes for heating elements and top panel to
cool off to avoid accidental burning of skin.
maintenance to reduce the risk of electric shock or damage
Media LED Light
to persons.
1. Unplug the unit from power outlet.
2. Remove the firebox from the front of the mantel and
may break if bumped, struck of dropped. Care must be
taken when handling the glass.
3. Remove the loose media from the unit (if applicable).
4. Remove the 14 screws around the back panel of the
Needle Nose Pliers
CAUTION: If unit was operating prior to servicing allow
WARNING: Disconnect power before attempting any
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
firebox and the 3 along the middle of the panel (Figure
2).
ure 3 & 4)
ing the tab to the left and opening the door.
ing needle nose pliers to depress the tab on the mount-
ing standoffs and gently lift the board off.
with new connection.
Flat Head Screwdriver
Needle Nose Pliers
CAUTION: If unit was operating prior to servicing allow
WARNING: Disconnect power before attempting any
remove front glass assembly (glass lifts off).
CAUTION: Even though the glass is safety glass it
firebox and the 3 along the middle of the panel (Figure 2).
15