Table of Contents
Advertisement
MB148 BOARD (9/9) IC6301 R5F3650KCDFB (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
SIRCS_IN
2
FAN CONT2
3
FL_D_OUT
4
NO_USE
5
FL_CLK
6
BYTE
7
CNVss
8
NO_USE
9
NO_USE
10
RESET
11
Xout
12
Vss
13
Xin
14
Vcc1
15
CEC_TX_RX
16
NO_USE
17
KEY_INT
18
AC_CUT
19
BD_IF_START
20
NO_USE
21
NO_USE
22
NO_USE
23
BD_IF_REQ
24
NO_USE
25
PCONT_FL
26
LED_PWM 1
27
NO_USE
28
NO_USE
29
TXD1
30
RXD1
ON CHIP DEBUG /
31
CLK1
32
NO USE / RTS1
33
DAMP_SDAO
34
DAMP_SCLO
35
DC_DET
36
PCONT1
37
PCONT2
38
PCONT3
39
EPM
40
STA516_POWER
41
NO_USE
42
FAN_ON
43
NO_USE
44
CE
45
ST_SDA
46
ST_SCL
47
PVDD_CONT
48
DRIVER_RST (EN)
49
NO_USE
50
DAMP_PDN
51
DAMP XRST
52
DAMP_XMUTE
53
NO_USE
I/O
I
SIRCS signal input from the remote control receiver
Fan motor speed control signal output terminal control by DA converter
O
Port output higher, speed slower
O
Serial data output to the fl uorescent indicator tube driver
-
No used
O
Serial data transfer clock signal output to the fl uorescent indicator tube driver
I
External data bus width selection signal input terminal
I
Processor mode selection signal input terminal
-
No used
-
No used
System reset signal input from the reset signal generator and reset switch "L": reset
I
For several hundreds msec. After the power supply rises, "L" is input, then it change to "H"
O
System clock output terminal (8MHz)
-
Ground terminal
I
System clock input terminal (5MHz)
-
Power supply terminal (+3.3V)
I/O
CEC serial data input/output with the HDMI connector
-
No used
I
Key wake-up signal input terminal
I
AC cut detection signal input terminal "L": AC cut
O
Ready signal output to the BD decoder "H": ready
-
No used
-
No used
-
No used
I
Request signal input from the BD decoder
-
No used
Power supply on/off control signal output terminal for fl uorescent indicator tube driver "H":
O
power on
O
LED drive signal output terminal
-
No used
-
No used
O
No used
I
No used
I
No used
O
No used
I/O
Two-way data bus with the DAMP processor
I/O
Serial data transfer clock signal output to the DAMP processor
I
Speaker DC detection signal input terminal "L": speaker DC is detected
O
Power supply on/off control signal output terminal "H": power on
O
Power supply control signal output terminal
O
Power supply on/off control signal output terminal "H": power on
O
EPM for update used
O
STA516 IC Power Control, "H": power on
-
No used
O
Power supply on/off control signal output terminal for fan motor "H": power on
-
No used
I
Chip enable signal input terminal
I/O
Two-way data bus with the FM receiver
I/O
Serial data transfer clock signal output to the FM receiver
O
Power Supply PVDD control for eco used
O
Reset signal output to the power amplifi er "L": reset
-
No used
O
DAMP Driver Standby Control
O
Reset signal output to the DAMP processor "L": reset
O
Muting on/off control signal output to DAMP processor "L": muting on
-
No used
HBD-E385/E390/T39
Description
77
Advertisement
Table of Contents
