Table of Contents
Advertisement
■
Activating Tone Function
Press [TONE] to switch the Tone function ON (or
OFF).
•
"
" appears when the Tone function is ON.
Note:
◆ You cannot use the Tone and CTCSS/ DCS functions at the
same time. Switching the Tone function ON after activating
the CTCSS/ DCS deactivates the CTCSS/ DCS function.
◆ When you access repeaters that require 1750 Hz tones, you
need not activate the Tone function. Press [CALL] without
pressing the PTT switch to transmit a 1750 Hz tone (default
setting).
■
Selecting a Tone Frequency
1 While the Tone function is ON, press [F],
[TONE].
2 Turn the Tuning control or press [ ]/ [ ] to
select the desired tone frequency.
3 Press [ ] or [MNU] to complete the setting.
Otherwise, press [PTT] to cancel.
Available Tone Frequencies
F
e r
. q
F
e r
N
. o
N
. o
H (
) z
H (
0
1
6
7
0 .
1
2
9
7
0
2
6
9
3 .
1
3
1
0
0
3
7
1
9 .
1
4
1
0
0
4
7
4
4 .
1
5
1
0
0
5
7
7
0 .
1
6
1
1
0
6
7
9
7 .
1
7
1
1
0
7
8
2
5 .
1
8
1
1
0
8
8
5
4 .
1
9
1
2
0
9
8
8
5 .
2
0
1
2
1
0
9
1
5 .
2
1
1
3
1
1
9
4
8 .
2
2
1
3
Note:
◆ 42 different tones are available for the transceiver. These 42
tones includes 37 EIA standard tones and 5 non-standard
tones.
◆ To transmit a 1750 Hz tone, simply press [CALL] without
pressing the PTT switch (default setting). Release [CALL] to
quit transmitting. You can also make the transceiver remain in
the transmit mode for 2 seconds after releasing [CALL]; a
1750 Hz tone is not continuously transmitted. Access Menu
No. 24 (1750 HOLD) and select "ON".
◆ If you desire to assign [CALL] for recalling the Call channel in
place of transmitting the 1750 Hz tone, access Menu
No. 23 (CALL KEY) and select "CALL".
. q
F
e r
. q
F
N
. o
N
. o
) z
H (
) z
4 .
2
3
1
4
1
3 .
3
4
2
0
0 .
2
4
1
4
6
2 .
3
5
2
3
5 .
2
5
1
5
1
4 .
3
6
2
7
2 .
2
6
1
5
6
7 .
3
7
2
0
9 .
2
7
1
6
2
2 .
3
8
2
4
8 .
2
8
1
6
7
9 .
3
9
2
8
8 .
2
9
1
7
3
8 .
4
0
2
3
0 .
3
0
1
7
9
9 .
4
1
2
7
3 .
3
1
1
8
6
2 .
4
2
2
1
8 .
3
2
1
9
2
8 .
6
5 .
3
3
2
0
3
5 .
AUTOMATIC REPEATER OFFSET
This function automatically selects an offset direction,
according to the frequency that you select on the
2 m band. The transceiver is programmed for offset
direction as shown below. To obtain an up-to-date
band plan for repeater offset direction, contact your
national Amateur Radio association.
144.0
S: Simplex
Note: Automatic Repeater Offset does not function when
Reverse is ON. However, pressing [REV] after Automatic
Repeater Offset has selected an offset (split) status, exchanges
the receive and transmit frequencies.
1 Press [MNU].
2 Turn the Tuning control or press [ ]/ [ ] to select
Menu No. 5 (AUTO OFFSET).
3 Press [ ] or [MNU].
4 Turn the Tuning control or press [ ]/ [ ] switch
the function ON or OFF.
5 Press [ ] or [MNU] to store the setting.
Otherwise, press [PTT] to cancel.
Note: If you select the frequency within the amateur radio band
on the B-band, the Automatic Repeater Offset function is also
activated in any modes.
e r
. q
H (
) z
0
6
5 .
1
0
7 .
1
8
1 .
2
5
7 .
2
9
1 .
3
3
6 .
4
1
8 .
5
0
3 .
5
4
1 .
5 OPERATING THROUGH REPEATERS
145.6
145.8
S
–
146.0 MHz
S
13
Advertisement
Table of Contents
Troubleshooting
