Page of 2
Download Bookmark Comment

RCA RTD3131 User Manual

Rca home theater system user manual.
Hide thumbs
   
FCC Information
Important Information
Important Information
This device complies with part 15 of the FCC
Ventilation
Important battery information
THE LIGHTNING FLASH AND ARROWHEAD WITHIN
CAUTION:
Rules. Operation is subject to the following two
You must adequately ventilate the product. Make
• Do not mix different types of batteries or new
This product utilizes a laser. Use of controls or
THE TRIANGLE IS A WARNING SIGN ALERTING YOU
USER MANUAL
conditions: (1) This device may not cause harmful
and old batteries. Do not use rechargeable
sure there is adequate space around the unit
adjustments or performance of procedures other
OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT.
batteries.
interference, and (2) this device must accept any
to provide proper air flow for ventilation. See
than those specified may result in hazardous
THE EXCLAMATION POINT WITHIN THE TRIANGLE
• In order to avoid any risk of explosion, observe
interference received, including interference that
diagram.
radiation exposure. Do not open covers and do
IS A WARNING SIGN ALERTING YOU OF IMPORTANT
the polarities indicated inside the battery
may cause undesired operation.
not repair yourself. Refer servicing to qualified
compartment. Replace only with the type of
INSTRUCTIONS ACCOMPANYING THE PRODUCT.
persionnel.
RTD3131
7 cm
batteries specified. Do not dispose of them in a
This equipment has been tested and found to
Visible and invisible laser radiation when open
CAUTION: TO REDUCE THE RISK OF ELECTRIC
RISK OF ELECTRIC SHOCK
fire or recharge them.
comply with the limits for a Class B digital device,
and interlocks defeated.
10 cm
10 cm
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
• If you are not using the remote control for a long
DO NOT OPEN
pursuant to part 15 of the FCC Rules. These limits
DO NOT STARE INTO BEAM.
USERSERVICEABLE PARTS INSIDE. REFER SERVICING
period of time, remove the batteries.
are designed to provide reasonable protection
WARNING: SHOCK HAZARD
TO QUALIFIED SERVICE PERSONNEL.
against harmful interference in a residential
Please respect the environment and
- DO NOT OPEN
prevailing regulations. Before you
installation. This equipment generates, uses
7 cm
WARNING
dispose of batteries or accumula-
and can radiate radio frequency energy and, if
10 cm
AVIS: RISQUE DE CHOC
To reduce the risk of fire or electric shock, do
tors, ask your dealer whether they
not installed and used in accordance with the
not expose this product to rain or moisture. The
are subject to special recycling and if
ÉLECTRIQUE-NE PAS OUVRIR
instructions, may cause harmful interference to
apparatus shall not be exposed to dripping or
they will accept them for disposal.
This class B digital apparatus complies
radio communications.
splashing and that no objects filled with liquids,
with Canadian ICES-003.
This product complies with DHHS Rules 21
such as vases, should be placed on the apparatus.
Cet appareil numérique de la classe B
SEE MARKING ON BACK OF PRODUCT
However, there is no guarantee that interference
CFR Subchapter J.
Applicable at the date of
Illustrations contained in this document are for
est conforme à la norme NMB-003
representation only.
will not occur in a particular installation. If this
manufacture.
du Canada.
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
equipment does cause harmful interference
TO RAIN OR MOISTURE.
to radio or television reception, which can be
For your safety
Important Safety Instructions
determined by turning the equipment off and
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
The AC power plug is polarized
on, the user is encouraged to try to correct the
THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
(one blade is wider than the
interference by one or more of the following
other) and only fits into AC
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH
Please read and save for future reference.
Protect the power cord from being walked on
measures:
power outlets one way. If the
THE SAME OR EQUIVALENT TYPE.
Some of the following information may not apply
or pinched particularly at plugs, convenience
Reorient or relocate the receiving antenna.
plug won't go into the outlet
WARNING: MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD REMAIN READILY
to your particular product; however, as with any
receptacles, and the point where they exit from
I n c r e a s e t h e s e p a r a t i o n b e t w e e n t h e
completely, turn the plug over
the apparatus.
electronic product, precautions should be observed
OPERABLE DURING INTENDED USE. IN ORDER TO DISCONNECT THE APPARATUS FROM MAINS
equipment and receiver.
and try to insert it the other way.
during handling and use.
Only use attachments / accessories specified by
COMPLETELY, THE MAINS PLUG SHOULD BE DISCONNECTED FROM THE MAINS SOCKET OUTLET
Connect the equipment into an outlet on a
Read these instructions.
the manufacturer.
COMPLETELY.
circuit different from that to which the receiver
If it still won't fit, contact a qualified electrician to
Keep these instructions.
Use only with a cart, stand, tripod,
is connected.
change the outlet, or use a different one. Do not
Service information
DVD copy protection
Heed all warnings.
bracket, or table specified by the
]
Consult the dealer or an experienced radio /
attempt to bypass this safety feature.
Follow all instructions.
manufacturer, or sold with the
This product should be serviced only by those
In accordance with the DVD standard, your DVD
TV technician for help.
Do not use this apparatus near water.
apparatus. When a cart is used,
specially
trained
in
appropriate
servicing
player is equipped with a Copy Protection system,
use caution when moving the
Removing the power plug is the only way to
Clean only with a dry cloth.
techniques.
which can be switched on and off by the DVD
Portable Cart
Do not block any ventilation openings. Install in
cart / apparatus combination to
WARNING: Changes or modifications to this unit
completely remove power from your product. Make
Main plug is used as the disconnect device,
disc itself, in order to make any recording of the
Warning
accordance with the manufacturer's instructions.
avoid injury from tip-over.
not expressly approved by the party responsible
sure the power plug remains easily accessible.
it shall remain operable and should not be
relevant DVD disc onto a videotape of very poor
Do not install near any heat sources such as
Unplug this apparatus during lightning storms
for compliance could void the user's authority to
obstructed during intended use. To be completely
picture quality, or even impossible. This product
radiators, heat registers, stoves, or other apparatus
or when unused for long periods of time.
disconnected the apparatus from supply mains, the
operate the equipment.
Note
incorporates copyright protection technology
(Including amplifiers) that produce heat.
R e fe r a l l s e r v i c i n g to q u a l i f i e d s e r v i ce
main plug of the apparatus shall be disconnected
that is protected by method claims of certain U.S.
This DVD player is designed and manufactured to
Do not defeat the safety purpose of the polarized
personnel. Servicing is required when the
from the mains socket outlet completely.
patents and other intellectual property rights
apparatus has been damaged in any way, such
respond to the Region Management Information.
or grounding-type plug. A polarized plug has
Caution
owned by Macrovision Corporation and other
two blades with one wider than the other. A
as the power cord or plug is damaged, liquid
If the Region number of a DVD disc does not
This Home Theater has earned
rights owners. Use of this copyright protection
Invisible laser radiation when open and interlocks
grounding type plug has two blades and a third
has been spilled or objects have fallen into the
correspond to the Region number of this DVD
the ENERGY STAR.
defeated. Avoid exposure to beam. Class 1 laser
technology must be authorized by Macrovision
apparatus, the apparatus has been exposed to
grounding prong. The wide blade or the third
player, this player cannot play the disc. The Region
product.
Corporation, and is intended for home use only
prong is provided for your safety. If the provided
rain or moisture, does not operate normally, or
number for this DVD player is Region 1.
This system must be opened only by qualified
unless otherwise authorized by Macrovision
plug does not fit into your wall outlet, consult
has been dropped.
technicians to prevent accidents caused by the
Corporation Reverse engineering or disassembly
an electrician for replacement of the obsolete
It's important to read this instruction prior to using your new product for the first time.
outlet.
laser beam.
is prohibited.
- 1 -
- 2 -
- 3 -
Important Safety Instructions
Connections and Setup
Connections and Setup
Connections and Setup
Additional safety information
Using OPTICAL DIGITAL IN jack
Using AUDIO IN jack
• Where the mains plug or an appliance coupler is used as a disconnect device,the disconnect device shall
Front speaker placement
1. Connect the OPTICAL DIGITAL IN jack on the
1. Connect the Ø3.5mm AUDIO IN jack on the
• Apparatus shall not be exposed to dripping or
If your product operates on batteries, adhere to the
remain readily operable.
Note: When connecting the speakers,
back of the unit to the OPTICAL DIGITAL OUT jack
front panel of the unit to the headphone output
splashing and no objects filled with liquids, such as
• Other important use and cleaning information at the end of the booklet.
For best results, follow the speaker placement
following precautions:
make sure the polarities ("+" speaker
on VCR, TV, Set Top Box or other component.
on mp3 players.
vases, shall be placed on the apparatus.
below.
wire to "+" on the receiver. For example,
A. Any battery may leak electrolyte if mixed with a
Connecting to your TV (VIDEO)
2. Press the DIGITAL button on the remote control
2. Press either SOURCE on the main unit or AUDIO
• Always leave sufficient space around the product for
red wire to red terminal on the receiver)
different battery type, if inserted incorrectly, or if all
to activate the sound from the external source.
IN on the remote control to select AUDIO IN
Alignment
Method 1
ventilation. Do not place product in or on a bed, rug,
of speaker wires and terminals match. If
batteries are not replaced at the same time.
Align the center speaker evenly with (A) or slightly
Composite video jack (yellow)
3. Press the SURROUND button on the remote
mode.
in a bookcase or cabinet that may prevent air flow
• If your television is a high definition
the cords are reversed, the sound will be
B. Any battery may leak electrolyte or explode if disposed
control to select the sound mode.
3. Press the SURROUND button on the remote
behind (B) (the left and right speakers), but not
• The basic video jack is color-coded yellow.
through vent openings.
television, use the unit's progressive
distorted. Do not let the speaker wires
of in fire or an attempt is made to charge a battery
control to select the sound mode.
ahead of them.
• Video cable (yellow) is supplied for the connection
• Do not place lighted candles, cigarettes, cigars, etc.
scan output to get the highest possible
touch each other, it will damage the Home
not intended to be recharged.
for good picture quality.
on the product.
video resolution. Set the Progressive Scan
Theater's amplifier.
Note
C. Discard leaky batteries immediately. Leaking batteries
• Connect the video OUT jack on the receiver to
• Connect power cord only to AC power source as
option in the Video menu to On.
Ø3.5mm to Ø3.5mm audio cables (not included).
can cause skin burns or other personal injury. When
the Video IN jack on your TV so the video content
• If one of the devices is not working, check
marked on the product.
discarding batteries, be sure to dispose of them in the
Positioning speakers
goes from the receiver to the screen.
that all the cables have been inserted
• Care should be taken so that objects do not fall into
proper manner, according to your state/provincial and
• Suggest using Ø3.5mm AUDIO IN
properly into the jacks.
the product.
local regulations.
3
jack for MP3 player and AUX IN
• Connecting mono components to your
• Do not attempt to disassemble the cabinet. This
D. Battery shall not be exposed to excessive heat such
receiver: If your component has only one
jacks for equipment such as TV,
1
product does not contain customer serviceable
as sunshine, fire or the like.
output for audio (mono), connect it to the
VCR, Satellite or Cable Box.
components.
white audio jack on the receiver and don't
• If the AUX IN (or AUDIO IN) audio signal
use the cable's red plugs.
Connections and Setup
is mono, you may not receive audio on
all speakers.
2
Rear of the unit
Accessories provided
Getting sound from external sources
Connecting the speakers
such as TV
Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each
1
Angle
speaker to the corresponding color terminal at the back of the unit. Press down the tab to open the
Using AUX IN (ANALOG R/L) jacks
DIGITAL
Rear of the unit
Place the left and right speakers to form a 45-
AUDIO IN
terminal and insert the wire. Release the tab to lock wire in the terminal.
3
4
1. Connect the AUX IN (ANALOG R/L) jacks on the
AUX IN
degree angle with your favorite viewing position
Method 2
back of the unit to the AUDIO OUT jacks on VCR,
Courtesy Dolby Laboratories
OK
Front Speakers
to duplicate the soundtrack mixer's perspective.
Component video jacks (Pr, Pb, Y)
TV, Set Top Box or other component.
Center
1. Left, Right (Front Speakers)
• The component video jacks are color-coded green,
2. Press the AUX IN button on the remote control
Speaker
Right
Left
+
-
SLOW
Front speakers carry primarily music and sound
Height
blue and red.
to activate the sound from the external source.
+
-
effects.
The three front speakers should be as close as
• Additional component video cables (not supplied)
3. Press the SURROUND button on the remote
A - B
DISC
possible to the same height. This often requires
are required to provide best picture quality. They
Green
control to select the sound mode (5.1 Channel
2. Center
RCR 192 AA7
Purple
placing the center speaker directly on top (A) or
are usually color-coded green, blue and red.
In surround mode, the center speaker carries
Remote control and 2
Left and right
Center speaker
Subwoofer
Left and right
<5.1ch> or Stereo mode) - the receiver will
beneath (B) the TV set.
• Connect the component video OUT jacks on the
Red
White
AAA batteries
front speakers
Surround
most of the dialog as well as music and effects.
display your selection on your TV screen.
Speakers
receiver to the component video IN jacks on your
It should be set between the left and right
TV so the video content goes from the receiver to
SpeakerS
peakers.
Composite
Subwoofer
SR
SL
SUB CEN FR
FL
the screen.
Video Cable
3. Surround (Rear Speakers)
Insert
A
The surround speakers' overall sound balance
should be as close as possible to the front
Press
Things to consider before you connect
peakers. Proper placement is vital to establish an
Y
• Ensure that the mains supply in your house
• The humidity of the room should not exceed 75%.
evenly distributed sound field.
complies with that indicated on the identification
P
If you have to use the unit outdoors, do not expose
B
Gray
Blue
4. Subwoofer
sticker located on the back of your unit.
it to rain or splashing water. The apparatus should
P
A subwoofer is designed to reproduce powerful
• Install your unit horizontally, away from
R
not be exposed to dripping or splashing and no
low bass effects (explosions, the rumble of
B
any source of heat (fireplace) or appliances
objects filled with liquids, such as vases, should
Rear Speakers
Release
spaceships, etc.).
creating strong magnetic or electric fields. The
be placed on the apparatus.
(Surround Sound)
components of this unit are sensitive to heat.
• Moving the unit from a cold place to a warm one
Right
Left
The maximum ambient temperature should not
can cause condensation on some components
Note: Center speaker provided with this
exceed 35°C / 95°F.
inside the unit. Let the condensation disappear
To adjust each speaker volume level for optimum listening experience.
unit is magnetically shielded to protect
• Leave enough space around the unit to allow
on its own before turning the unit on again.
(1) Press the LEVEL button on the remote control to select Left (front Left speaker).
your TV set. It is not recommended to place
Rear of the unit
adequate ventilation: 10 cm/4 inches on either
• Before moving the unit, make sure the disc tray
(2) Press the VOL+/VOL- buttons to adjust the value up or down (between -10dB and +10dB).
the front speakers, surround speakers and
side and above the top, and 5 cm/2 inches at the
is empty.
(3) Repeat step (1) and (2) for the other speakers Right, Center, Left Surr., Right Surr., Subwoofer and Loudness (on/off).
subwoofer near the TV set.
rear.
Speaker gains may be set to levels of up to +10dB, actual max levels may also depend on your Volume Setting.
Rear of the unit
- 4 -
- 5 -
- 6 -
- 7 -
Connections and Setup
Overview of Controls
Overview of Controls
Playing Discs - Basic Functions
Basic Playback Operations
Better surround placement
No adjacent walls
ON•OFF:
Turns on/off the unit.
SURROUND: Changes
the
Surround
sound
Compatible discs
Variable slow motion
Surround speakers can go on stands facing each
Location
DVD:
Selects the DVD mode.
1. Press SLOW button on the remote in play mode.
Notes
setting. Press the button to select
other to approximate sidewall mounting (A), or to
• DVD, DVD-R, DVD-RW, DVD+R, DVD+RW
If possible, place surround speakers to either side
2. Each time the SLOW button is pressed the
DIGITAL:
Selects the Optical Digital input (for listening
• When you press STOP, the unit stores the
the sides or rear of the viewing area, aimed upwards;
between 5.1 Channel and Stereo
• CD, CD-R, CD-RW
of the listening area, not behind it.
speed of slow-motion playback changes in the
point where playback was interrupted. If
they can go right on the floor, or preferably, a few
to audio input from connected TV, VCR or
modes.
Height
Compatible formats
following sequence:
you press PLAY again, playback resumes
feet off the floor such as on end tables (B).
SetTop BOX).
If space permits, install surround speakers 2-3 feet
Using remote control to navigate through
from this point.
AUDIO IN:
Selects the Front Audio Input.
• DVD, JPEG
1/ 2
1/ 4
1/ 6
1/ 8
above viewers. This helps to minimize localization
the on-screen menus
• To stop playback completely or to start
• CD
AUX IN:
Selects the Auxiliary input (for listening to
effects.
DIGITAL
again from the beginning, press STOP twice.
Use
/
/ / and OK on the remote control to
3. Press PLAY to resume normal playback.
audio input from connected TV, VCR or Set-
Aiming
Regional coding
If the unit is left in STOP mode for more than
navigate through the on-screen displays (the DVD
Aim surround speakers straight across the room,
Top BOX).
AUDIO IN
Changing chapter/track
5 minutes without any user interaction, a
player's menu, the Info Display that appears during
Your unit has been designed to process regional
not down at viewers, to help create a more open,
0-9:
Number entry.
management information stored on DVD discs.
While the disc is playing, press the CH+/- button to
playback, or a disc's menu).
screen saver is activated. At the end of 30
spacious surround sound field.
CLEAR:
Quits the current setting manually from the
The regional code for your unit is 1. Discs that have
go immediately to the next or previous chapter, or
minutes without any user interaction, the
AUX IN
Use
/
/ / on the remote to move through on-
TV screen without saving change.
a different regional code will not play.
to the next or previous track.
unit switches off automatically.
screen menus in the direction of the arrow button
INFO:
Accesses the display information.
Operating the DVD receiver
Zoom into an image
(e.g., to move right, press ). The arrow buttons
Test tone/Channel balance
TITLE:
Accesses the title menu of DVD discs.
1. While a disc is playing, press ZOOM repeatedly to
Display Info (information)
are used to highlight an option. Once highlighted,
1. Turn on your television set.
Channel balance
DISC MENU: Accesses the disc menu during playback.
enlarge the image in 3 levels (
,
and
).
1. Press INFO on the remote while a disc is playing
press OK to select the option that is highlighted.
2. Press ON•OFF on the remote control or ON/
1
2
3
Your receiver is equipped with a test signal
OK:
Confirms your selection.
2. Move from one area to another (pan) using the
STANDBY located on the front panel of the unit.
to display information on operation status.
generator to help you balance the audio level for
/
/ / :
To navigate through the menus.
arrow buttons.
The first banner shows the elapsed time from
Press DVD on the remote control.
each channel. See Audio Setup under The Setup
MUTE:
Mutes and restores the sound.
3. To turn ZOOM off, press the ZOOM repeatedly
the beginning of the title which is currently
Menu section of Instruction Book for details on
Loading disc
playing.
until the
is displayed.
SETUP:
Enters Setup menu.
how to access this feature .
2. Press INFO again for Title and Chapter.
RETURN:
1. Press
on the front panel of the unit to open
As the signal "travels" from channel to channel,
Returns to the normal operation after using
Note
Shows the number of the title/chapter currently
Random playback
use the VOL controls to adjust each channel to the
the disc tray.
the setup menu.
Insert 2 "AAA" batteries in the remote
playing and total titles/chapter on disc.
While the audio CD is playing, press the RANDOM
same loudness level.
2. Place a disc onto the disc tray with the label side
control prior to use.
VOL +/- :
Adjusts the sound volume.
3. Press INFO a third time for Audio.
button on the remote control to activate/inactivate
up.
Alternative Surround Placement
Level adjustment and surround channel level
Shows the type of the audio currently selected
CH+/ , CH–/
: Directly accesses the next or previous
the random playback.
3. Press
again to close the disc tray.
expectation
Rear wall
is displayed.
chapter (DVD) or track (CD).
Random: All tracks will be played randomly.
If rear wall mounting is the only choice, aim the
Even though you may adjust the surround channels
4. Press INFO a forth time for Subtitle.
REV:
Starts reverse accelerated play.
Playback
Random Off: To resume normal playback.
to be as loud as the others on the test signal, you
speakers at each other (A), towards the front (B) or
Shows the subtitle number and language
Switch the unit and the TV set on.
PLAY:
Starts playing a disc.
towards the sidewalls (C, D).
might find that surround channels seem quieter
Types of menus
currently selected is displayed.
1. After
loading
a
disc,
playback
starts
for actual TV and Movie content. This is because
Experiment with placement until sounds seem to
FWD:
Starts forward accelerated play.
• Disc menu — The appearance and contents of
5. Press INFO a fifth time for Angle.
automatically, or the disc menu appears. If the
producers use surround for subtle atmospherics
Shows the current angle is displayed.
surround you, rather than come from behind you.
SLOW:
this menu varies according to the type of disc
Selects SLOW motion function.
disc menu appears, select the Play option to
and ambience, and only rarely for special effects.
you have inserted. It is separate from the Setup
STOP:
Stops playback.
begin playback.
menu.
PAUSE:
Freezes frame, accesses frame advance.
Overview of Controls - Front Panel Controls
SLOW
2. Press STOP to stop playback.
• Setup menu — Press SETUP to access this menu.
DVD Info Display
AUDIO:
Accesses the audio function.
Accelerated play
ANGLE:
Accesses the camera angle function for DVD disc.
SOURCE button - Selects the input sources.
While the disc is playing, press REV or FWD one or
ZOOM:
Accesses the Zoom function.
Time
00:18:18
Press repeatedly to select:
more times to vary the speed and direction of the
Player Menu
: English
• DVD – to watch DVD videos.
SUBTITLE:
Selects the subtitle languages or turns
accelerated play. Press PLAY to resume normal
OPEN/CLOSE button -
PLAY/PAUSE button -
• OPTICAL DIGITAL IN (rear) / AUX IN (rear) /
AUDIO IN jack -
: English
subtitle off ( if available).
playback.
Opens and closes the
Starts/pauses playing
AUDIO IN (front) - to listen to the audio input
Title
1/21
Chapter
7/29
connects audio
MEMORY:
Creates programs.
disc tray.
a disc.
from the connected TV, VCR or Set Top Box.
: English
devices.
Pause
RANDOM:
Turns on/off random playback on CDDA discs.
Disc Menu
: English
While the disc is playing, press PAUSE once for
Audio
1/3
6 ch Eng
SUBWOOFER: Selects among subwoofer output levels
A - B
DISC
freeze frame. Press PLAY to resume normal play-
(soft/balance/strong/powerful).
back.
REPEAT A-B: Performs point-to-point repeat playback on
Subtitle
1/6 Eng
Default
a DVD or CD.
Frame advance
REPEAT DISC: Repeats chapter or title of a DVD.
1. Press PAUSE twice. "Step" is displayed.
Angle
1/1
2. Each time you press PAUSE button, the picture
DVD indicator
ON/STANDBY button-
ON/STANDBY indicator
VOLUME control -
Repeats single track or whole CD.
AUX IN indicator
Switches the unit on
Adjusts the volume.
advances one frame.
LEVEL:
Toggles speaker channels for different level
and off.
AUDIO IN indicator
RCR 192 AA10
3. Press PLAY to resume normal playback.
settings. Adjust the value using VOL +/-.
DIGITAL indicator
- 8 -
- 9 -
- 10 -
- 11 -

   Related Manuals for RCA RTD3131

   Summary of Contents for RCA RTD3131

  • Page 1

    (2) this device must accept any interference received, including interference that may cause undesired operation. RTD3131 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits...

  • Page 2

    Basic Playback Operations DVD Programmable Memory Playing CDs Repeating a specific title/chapter (DVD) You can combine your favorite titles/chapters and Make sure that a disc you want to play is compatible While the disc is playing, press the REPEAT DISC play them in the order you determine.

Comments to this Manuals

Symbols: 0
Latest comments:
  • bill Mar 30, 2014 11:05:
    I can't hook up my headphones​,they wont work.