Page 1
Service SR5009 / U1B/N1B/N1SG /K1B Manual AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
Contents ABOUT THIS MANUAL .............3 CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK .....93 What you can do with this manual ..........3 LEVEL DIAGRAM ..............94 Using Adobe Reader (Windows version) ........4 BLOCK DIAGRAM ..............100 SAFETY PRECAUTIONS ............6 POWER DIAGRAM ..............101 NOTE FOR SCHEMATIC DIAGRAM .........7 WIRING DIAGRAM ..............102 NOTE FOR PARTS LIST ............7...
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
TECHNICAL SPECIFICATIONS n Audio section n Wireless LAN section • Power amplifier Network type Rated output : (wireless LAN standard): Conforming to Wi-Fi®z1 Front : Security : WEP 64 bit, WEP 128 bit 100W+100W(8Ω, 20Hz - 20kHz with 0.08% T.H.D.) WPA/WPA2-PSK (AES) 140W+140W(6Ω, 1kHz with 0.7% T.H.D) WPA/WPA2-PSK (TKIP)
PRECAUTIONS DURING SERVICE Initializing This Unit Initialize this unit if you have replaced the microcomputer, one of the parts around the microcomputer, or the digital PCB. Press the power button to turn off the power. Hold down buttons "TUNER PRESET CH -" and "TUNER PRESET CH +" at the same time and press the power but- ton to turn on the power.
DISASSEMBLY • Remove each part in the order of the arrows below. • Reassemble removed parts in the reverse order. • Read "Precautions During Work" before reassembling removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 12
Explanatory Photos for DISASSEMBLY • The angles from which the photos are taken are shown by "Photo angle: A, B, C, D". • See the diagram below about the shooting direction of each photograph. • Photographs with no shooting direction indicated were taken from the top of the unit. •...
1. FRONT PANEL ASSY TOP COVER → FRONT PANEL ASSY Proceeding : (1) Remove the screws. View from the bottom (2) Cut the wire clamp, then remove the connector wires and FFC. Remove the STYLE PIN. Remove the HOLDER and screws. Front side CP4400 STYLE PIN...
3. HDMI PCB TOP COVER → BACK CHASSIS → Proceeding : HDMI PCB (1) Remove the screws. (2) Cut the wire clamp, then remove the connector wires and FFC. Front side STYLE PIN N1019 CON1 N1029 CON2 N7002 N7005 STYLE PIN (3) Remove the connector wire.
4. VIDEO PCB TOP COVER → BACK CHASSIS → → VIDEO PCB Proceeding : HDMI PCB (1) Remove the connector wire. Front side CN5004 CN5001 CN5000 CN5003 5. PREOUT PCB TOP COVER → BACK CHASSIS → → VIDEO PCB → PREOUT PCB Proceeding : HDMI PCB (1) Remove the connector wire.
MAIN PCB TOP COVER → BACK CHASSIS → → VIDEO PCB → PREOUT PCB Proceeding : HDMI PCB → MAIN PCB (1) Remove the screws. View from the bottom (2) Remove the connector wire. CP402 CP405 CP403 (3) Remove the connector wire. Remove the screws. CN4001 CP5003...
7. SMPS PCB TOP COVER → BACK CHASSIS → Proceeding : SMPS PCB (1) Remove the connector wire. Remove the screws. CP4142 TO HDMI PCB N1029 8. TRANS POWER TOP COVER → BACK CHASSIS → → TRANS POWER Proceeding : HDMI PCB See "EXPLODED VIEW"...
SPECIAL MODE Special Mode Configuration Buttons No. 1 - 12 : Hold down buttons A, B and C at the same time and press the power button to turn on the power. No. 13 : Press the A and B buttons simultaneously while inserting the AC plug to turn the power on. Mode Button A Button B Button C Contents...
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up Hold down buttons "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. Press the "STATUS"...
Page 21
1.4. Error display See the table below for descriptions of displayed errors and countermeasures for these. Display order is q , w , e , r , t , y , u . Condition States Display TROUBLE SHOOTING The model name, brand name and region infor- F I R M mation written in the firmware are compared E R R O R...
Page 22
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware XXXX-XXXX-XXXX Version...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Turn the PANEL LOCK and REMOTE LOCK modes on and off. 2.2. Starting up Hold down buttons "M-DAX" and "ZONE2 SOURCE" at the same time and press the power button to turn on the power. Select the mode using the button "TUNER PRESET CH+", and press the button "STATUS"...
3. Selection Modes for Service-related Operations 3.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up Hold down buttons "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power. 3.3.
Page 25
3.4. DIAGNOSTIC MODE (Service Path Check Mode) 3.4.1. Actions This function is convenient for confirming problem paths in the product and executing a path check after repair. The Video and Audio paths can be checked. The backup data is not rewritten. 3.4.2.
Page 26
3.4.6. Audio system confirmation items fig. XX: See the block diagram of the fig.XXth. Paths confirmation item Display Settings Contents of confirmation Remarks Analog ( pass ) Input Source: CBL/SAT ・Check the audio output. Upper A 0 1 A N L G Input Mode: ANALOG fixed ・Check of Analog input ⇒...
Page 31
fig.04b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 33
fig.06 ADV8195 TMDS IN FRONT HDMI BUFFER TMDS OUTPUT HDMI OUT1 TMDS IN HDMI2.0 HDMI1 HDMI2.0 Matix SW Matix SW MN8647781 MN8647781 HDMI2 MX25L12845EMI-10G 128M TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 TMDS OUT HDMI4 HDMI Rx HDMI2.0 HDMI i/p Scaler_TX_OSD HDMI5...
Page 34
fig.07 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 36
fig.08b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 38
fig.09b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 40
fig.10b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 42
fig.11b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 43
fig.12 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 44
fig.13 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 46
fig.14b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM DSP_SL MIC(Mini Jack) EXT_SL...
Page 47
3.5. Protection History Display Mode 3.5.1. Actions This mode records and displays an event in which the THERMAL, ASO or DC protection was activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.5.2. Starting up Hold down buttons "ZONE2 SOURCE"...
Page 48
3.5.4. Clearing the Protection History There are two ways to clear the protection history. (1) Start Protection History Display Mode. Press the button "STATUS" to display the protection history. Press and hold the button "DIMMER" for 3 seconds. P R O T E C T H I S T O R Y : D C Press and hold the button "DIMMER"...
Page 49
3.6. Operation Info Mode 3.6.1. Actions This mode displays the accumulated operating time, power on count and each protection count. 3.6.2. Starting up Hold down buttons "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power. Select the "4.
Page 50
3.7. TUNER STEP mode 3.3.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.7.2. Starting up Hold down buttons "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power. Select the "5.
4. Protection Pass Mode 4.1. Actions • This mode allows the power to be turned on without activating protections. • This is the same as normal power-on, except that protections are not activated. 4.2. Operations Hold down buttons "DIMMER", "STATUS" and "SOUND MODE" at the same time and press the power button to turn on the power.
6. CX870 / CY920 Initialization mode 6.1. Actions The following items are initialized. (1) Favorites (2) Quick Select (3) Presets (4) Internet Radio Recently Played (5) Flickr contacts (6) User ID (7) Resume Playback station 6.2. Operations Hold down buttons "TUNER PRESET CH -" and "DIMMER" for at least 3 seconds while the power is on. Initializing Display I n i t i a l W a i t...
JIG FOR SERVICING The following jigs (extension cable kit) are used when repairing the PCBs. Order the jigs from your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for HDMI PCB -Items to Be Prepared- 8U- 110084S EXTENSION UNIT KIT 1 Set...
Page 54
Front side CN5004 CN5001 CN5000 CN5003 Front side CN5601 TO CP401 CN5602 (3) Remove the HDMI PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the HDMI PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB PREOUT PCB VIDEO Insulation sheet...
Page 55
(4) Connect the expansion cables. PCB FRONT CNT PCB HDMI PCB INPUT PCB FRONT CNT PCB VIDEO PCB INPUT PCB FRONT CNT PCB INPUT PCB PREOUT Connection table of Board to Board Ref. No. Ref. No. 17pin CP3404 FRONT CNT N1018 HDMI 11pin...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Proce- dure after PCB Name Ref. No. Description Remark Replace- ment U1018 R5F56108VNFP 32BIT SOFTWARE: Main HDMI U1020 R5F5210ABDFP SOFTWARE: Sub HDMI HDMI U1025 MX25L1606EM2I-12G 16M...
Page 57
1.3. File structure on USB Memory Copy the update files to the USB memory with the following structure: USB memory root Model Name Model Area Product ID SR5009U North America (U) 100100250100 SR5009N Europe (N) 100100250200 SR5009K China (K) 100100250500 + firmwares + 000100XXXXXX + APLD.bin...
Page 58
1.5. Start the update. Hold down buttons "TUNER PRESET CH +" and "STATUS" at the same time and press the power button to turn on the power. 1.6. Display during USB update The following message appears on the display after around 30 seconds Display U S B U p d t...
Page 59
1.10. About the error code See the table below for error codes and details of faults when the firmware is updated through USB memory. Error Details of Error code Display Coping strategies Code C o n n e c t i o n F a i l Disconnect and connect the USB Unable to detect USB.
Page 60
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. E r a s e f a i l Block Erase failed before rewriting If the FL display stops at the Error dis- Main.
Page 61
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. N o t M a t c h F i r m Firmware File in USB for unsup- If the FL display stops at the Error dis- ported Model name/area.
Page 62
Error Details of Error code Display Coping strategies Code This unit automatically retries several Invalid DeviceID in response or no times. Wait until the FL display stops. C o n n e c t i o n F a i l response from Sub for C com- If the FL display stops at the Error dis- mand.
Page 63
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. U p d a t i n g f a i l Abnormal data in Update Packet If the FL display stops at the Error dis- received from CX870 (CRCError).
Page 64
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. U p d a t i n g f a i l Failed to transit to BootLoader If the FL display stops at the Error dis- Mode.
2. Updating by DPMS Download the latest firmware from the internet and update the firmware. 2.1. Network Connection (1) System Requirements • A broadband internet connection • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Settings Internet Computer Modem ComputerLAN port / Ethernet connector...
Page 66
2.3. About the error code See the following table for details on the error code, details of the error code, display and coping strategies when updating the firmware from DPMS. (DPMS:Marantz Product Management Server). Error Details of Error code Display...
Page 67
Error Details of Error code Display Coping strategies Code Abnormal data in Update Packet U p d a t i n g f a i l Turn on the power again. Update will received from CX870 (PacketNo- start automatically. Error). E r a s e f a i l Block Erase failed before rewriting...
Page 68
Error Details of Error code Display Coping strategies Code Check the network connection. Update C o n n e c t i o n F a i l Connect Time Out by DPMS con- in an environment where there is a nection.
Page 69
Error Details of Error code Display Coping strategies Code NACK received in response or no U p d a t i n g f a i l Turn on the power again. Update will response from Sub for L com- start automatically.
Page 70
Error Details of Error code Display Coping strategies Code Check the network connection. Update C o n n e c t i o n F a i l IP Address acquisition failure in an environment where there is a (Time Out). small network load.
Page 71
Device display during firmware update Display of target device during firmware update. Target device Display Error code when an error occurs 08 - 0C M a i n 10 - 15 Main CPU * * * m i n 22 - 24 36 - 3E * * % 50 - 52...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DV voltmeter. (2) Place the unit in normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Contents Connections Playback Settings Tips Appendix Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. DThis indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (v p. 189). Channel output Sound mode (v p.
Page 74
Contents Connections Playback Settings Tips Appendix Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. 2-channel signal Multi-channel signal Analog /PCM Dolby Digital DTS-HD DTS Express DTS Dolby TrueHD Dolby Digital Plus Dolby Digital EX Dolby Digital Sound mode (v p.
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator on Does the power indicator on the the front panel flash in green front panel flash in red when the or white when the power is power is turned on? turned on?
2. Analog video COMPONENT/HDMI OUT NG Input CVBS Input OMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI TO "3 HDMI/DVI" To A <HDMI PCB> test point HDMI PCB CLAMP1000 7020-07508-020-0S [MP] C2174 N1019 CLAMP1001 R1374 U1050 C1293 R1371...
Page 77
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the following points? HDMI PCB Check the connection between Input CVBS:Check B : R2092 the PCBs. Input COPONENT:Check C COMPONENT-Y : R2089 COMPONENT-Cb : R2091 COMPONENT-Cr : R2090...
Page 78
Input CVBS Check the set value of each IC. Are the voltage values as follows? HDMI PCB The HDMI PCB is faulty. N1018 - 3pin : Hi(3.3V) N1018 - 4pin : Hi(3.3V) N1018 - 5pin : Lo(0V) Use the jigs to extend the HDMI PCB.
Page 79
Input COMPONENT Check the set value of each IC. Are the voltage values as follows? The HDMI PCB is faulty. HDMI PCB N1018 - 2pin : Lo(0V) N1018 - 6pin : Hi(3.3V) Use the jigs to extend the HDMI PCB. Is the power supply voltage Check the connection between the being output correctly?
(7) Are the HDMI output settings of the Blu-ray/DVD player correct? and set the HDMI output correctly. (8) If using a marantz Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES if using a Blu-ray/DVD player from another com- pany.
Page 81
(11) Are a picture and sound output when a different Blu-ray/DVD The Blu-ray/DVD player is faulty. player is used? Check the TV. Use a TV that supports HDCP. Computer monitors can- (12) Does the TV support HDCP? not be used. If the TV does not support 1080P, a picture cannot be (13) Does the TV support 1080P/4K? output even if the Blu-ray/DVD player is set to 1080P/4K.
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO Legacy BLOCK Audio output OK? COAX or OPT Don't care (PCM or DolbyDigital or dts…) CHECK3...
Page 83
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuit- Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 84
4.3. Analog audio No audio output. Is a voltage of ±7V supplied to INPUT Repair the ±7V power supply. PCB CN4006? Is there an audio signal in INPUT Repair the power amplifier. PCB CN401? Connect the connectors correctly. Is electron volume serial data being Is the connector correctly connected sent to INPUT PCB CN4200? with HDMI PCB?
5. Network/Bluetooth/USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn Is the LAN cable correctly inserted? on the power again. Check the connection environment Set the IP address, etc. correctly. If the IP settings are fixed, check that no Are the network settings of this unit correct? other devices have the same IP address and...
Page 86
The circuit between the AC inlet and N1029 Can a voltage (5V) be confirmed between pin 2 and pin 5 of is faulty. Check the SMPS PCB. N1029? Can an output voltage (3.3V) to Is D5V_POWER (U1018 uCOM 85pin) The circuit of D5V_POWER between U1070(DC-DC Conv.) be confirmed? "Hi"...
Page 87
5.2. Cannot connect to the Bluetooth Can a voltage (5V) be confirmed between pin 1 and pin 4 of N1036 on The circuit between the AC inlet and N1036 is faulty. HDMI PCB? Check the SMPS PCB. The circuit between N1036 of the HDMI PCB and Can a voltage (5V) be confirmed pin 10 of CP6001 on Bluetooth CP6001 of the Bluetooth PCB are faulty of wire or PCB?
Page 88
5.3. A connected USB device is not recognized. Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16 and FAT32-formatted mass storage class, MTP- Is the USB device supported by this unit? compatible devices and iPods (with the exception of some models).
6. SMPS DC 5V is not output. Replace the IC4140 (TOP258MG) and Is IC4140 (TOP258MG) damaged? D4142 / D4143 / D4144 / D4145. Are there the damage in D4142 / Has a fuse (F4140) broken? Replace the damaged part(s). D4143 / D4144 / D4145 / IC4140? Are there any short circuits caused by Repair the short circuited area(s) by the the soldering of the PCB?
Page 91
Operation waveform for each part Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) OPTION OPTION OPTION After secondary rectifications OPTION T4140 ● OPTION ● ● ● TR4140 IC4140 OPTION SMPS unit (Unloaded)
LEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15218FP ANALOG H/POUT + SPEAKER LINE IN GAIN + PCM1690 + PCM9211 + - - MUTE PRE OUT ZONE2 EXT IN (SR5009 ONLY) +30dB SP OUT 4.48Vrms/8Ω MAX SIGNAL LEVEL 0dBFS +20dB +20dB 1.41Vrms PCM1690 DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS...
Page 95
LEVEL DIAGRAM CENTER ch R2A15218FP + SPEAKER GAIN PCM1690 (SR5009 ONLY) + + - - MUTE PRE OUT EXT IN (SR5009 ONLY) +30dB SP OUT 4.48Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 1.41Vrms +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS +29dB +10dB +10dB -10dBFS -20dBFS(DIG.IN)
Page 96
LEVEL DIAGRAM SUBWOOFER ch R2A15218FP MUTE PRE OUT GAIN PCM1690 + + (SR5009 ONLY) - - MUTE PRE OUT EXT IN (SR5009 ONLY) +30dB MAX SIGNAL LEVEL Config1 DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS 0.88Vrms +20dB +20dB 0dBFS +10dB +10dB -10dBFS PREOUT 317mVrms -2dB...
Page 97
LEVEL DIAGRAM SURROUND ch R2A15218FP SPEAKER + GAIN PCM1690 + (SR5009 ONLY) + - - MUTE PRE OUT EXT IN (SR5009 ONLY) +30dB MAX SIGNAL LEVE SP OUT 4.48Vrms/8Ω 0dBFS 1.41Vrms +20dB +20dB 0dBFS Config2 DOLBY LIMIT LEVEL 1.41Vrms(ALLch-3dBFS) +29dB +10dB +10dB -10dBFS...
Page 98
LEVEL DIAGRAM SURR.BACK ch R2A15218FP + SPEAKER GAIN PCM1690 + (SR5009 ONLY) + - - MUTE PRE OUT EXT IN (SR5009 ONLY) +30dB SP OUT NON CLICP MAX SIGNAL LEVEL 4.0Vrms 4.48Vrms/8Ω SP OUT(D/A OUT) 0dBFS DOLBY LIMIT LEVEL 1.41Vrms(ALLch-3dBFS) 1.41Vrms +20dB +20dB...
Page 99
LEVEL DIAGRAM ZONE2 R2A15218FP from F-ch from SPEAKER DA SB-ch + LINE IN + MAIN NET/USB DAC BD3812F ZONE2 +30dB SP OUT 0dBFS PCM5100 2.0Vrms MAX SIGNAL LEVEL 2.00Vrms +20dB +20dB 0dBFS +10dB -10dBFS +10dB -20dBFS(DIG.IN) LINE IN 200mV -20dBFS PREOUT -18.0dB 16.0dB...
POWER DIAGRAM VCC DIAGRAM S1(AMP +B) AC OUTLET S2(+8V,-8V) MAIN TRANS Except SR AC CORD NET3.3V(CX870/MFI341S2164) NET1.2V(CX870) MAIN PWR ON NET1.8V(CX870:OPEN) NET1.9V(CX870)
Page 108
GUIDE L (A SIDE) GUIDE R (A SIDE) TOP GUIDE (A SIDE) H/P (A SIDE) H/P (B SIDE) USB (A SIDE) USB (B SIDE) 7028-07503-201-0 CN4402 G4401 C4473 BACK 7028-07503-301-0 H/P B'D C4472 JP4402 JK4401 7028-07503-601-0 TOP GUIDE B'D G4400 JP4403 C4486 C4463...
NET PHY TO ΦB BΦ TO CPU DM920_SPDIF NET/USB_MCK NET/USB_LRCK DIR/A.PLD NET/USB_BCK TO 1B NET/USB_DATA_/FR NET/USB_DATAF/FL NET3.3V FROM NET2.5V D.SUPPLY NET1.8V TO 2B NET1.2V DGND R1207 OPEN R1208 OPEN OPTION C1172 OPEN-1608 920PCK C1173 100N-K CX870 OPEN 920VD0 C1174 1N-K 920VD1 U1005 CY920 USE...
CPU LEVEL CHG TO 4B TO DIGITAL CNT REMOTE3.3V FROM SWM3.3V D.SUPPLY TO 5B M3.3V DGND OPEN SWM3.3V R1366 DGND 14 13 12 11 10 Q1032 RT1N141C FROM SCPURXD SUB CPU SCPUTXD TO 7B TO 6B TO CPU SCHEMATIC DIAGRAMS (5/32) 05-CPU_LEVEL_CHG GND LINE POWER+ LINE...
TO CPU LEVEL CHG TO SUB CPU TO DIR/A.PLD TO B6 TO MAIN DAC TO 4C TO 5C MAIN_POWER E_POWER1 E_POWER2 HDMI TX ADV8003_SPI_MO E_POWER3 (ADV8003) ADV8003_SPI_MI E_POWER4 R1385 OPEN ADV8003_SPI_CLK BDOWN R1386 OPEN TO 2C ADV8003_SPI_CS TO D.SUPPLY R1393 SCPU_POWER R1394 CPU_POWER...
SUB CPU TO A4 TO A9 TO C6 HDMI SW1 HDMI SW2 HDMI TX SCPU5V SCPU3.3V DGND FROM SBUBDOWN D.SUPPLY DSP1CLK DV_POWER2 DSP1MISO DV_POWER1 TO C7 DSP1MOSI CEC_POWER DSP1RST DA_POWER TO D5 DSP1CS DSP1FLAG0 TO D4 ADV7850_INT AVSDA HDMI RX AVSCL R1469 ADV7850...
TO D6 TO DIR/A.PLD TO SUB CPU TO 5D MP OPEN N1034 1.0-16-6PB-2 DSP1CS DSP1MISO DSP1MOSI DSP1CLK DGND DA3.3V MP OPEN R1562 OPEN N1027 1.0-16-10PB-2 DTCK DTDO R1566 OPEN R1567 DTMS TRST DTRST EMU0 DEMU0 R1568 EMU1 DTDI OPTION TABLE MODEL R1576 R1583...
DIR/A.PLD TO F2 TO F1 TO 9E TO B1 TO C5 TO 1D FROM HDMI RX HDMI RX NET PHY HDMI TX ADV7850 ADV7850 SUB CPU ※FILTER COMPONENTS VALUE TYPE TOLERANCE 680 Ω 0 Ω ≦ 5% R1907 METAL FILM OR CARBON ≦...
TO F5 TO F4 MAIN DAC TO 6F FROM FROM FROM FROM FROM DIR/A.PLD DIR/A.PLD DIR/A.PLD SUB CPU DA+5V A/DIN_R DAGND A/DIN_L DAGND 100N-K-1608 R1997 DACRTNGND R1998 100N-K-1608 DA+5V C2137 R1999 DAGND OPEN-1608 100-1608 DAGND R2002 TO DIGITAL CNT C2143 10U-K-2012 100-1608 TO F9...
OPTION D MAIN 3/3 B5 CN4701 OPTION E MAIN 2/2 M6 CP4202 MAIN 2/2 M9 HDMI_DIGITAL CNT M2 HDMI_DIGITAL CNT M4 PREOUT 2/2 K3 CP4205 HDMI_DIGITAL CNT G3 OPTION A TO N1016 HDMI_DIGITAL CNT G3 CN4006 TO CP4006 CN4703 TO CP4007 CP4203 TO N1013 CP4200...
CVBS INPUT SW NJM2595MTE1 INPUT OUT PUT AVR4/AVR3 SR5009 SW1 SW2 SW4 SW5 MUTE MUTE VIN 3 CBL/SAT VIDEO / ZONE2 PART VIN 4 * MODEL / AREA OPTION VIN 2 NOT USED V.AUX MODEL AVR4 AVR3 SR5009 E2/E1/E1C/JP U1B/N1B/K1B AREA OPTION A OPTION B...
FRONT_CNT PART TO N1033 CP3401 HDMI_DIGITAL CNT G8 CP3404 HDMI_DIGITAL CNT C4 TO N1018 AVR4_AVR3 VIDEO_F/CNT 1/3 O7 VIDEO_F/CNT 1/3 O4 VIDEO_F/CNT 1/3 O2 CP5004 TO CN5004 MAIN TRANS TAP CP5000 TO CN5000 CP5001 TO CN5001 PREOUT 1/1 b6 TO CN5601 OPTION B CP3403 SR5009 ONLY...
RC-5 PART SR5009 ONLY CHASSISGND SCHEMATIC DIAGRAMS (23/32) 23-VIDEO_RC5 GND LINE POWER+ LINE POWER- LINE COMPONENT ( Y ) ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL VIDEO SIGNAL...
TUNER / REG PART TO G3 OPTION A CP4003 TO CN4003 CP4002 TO CN4002 OPTION D SR5009 : 6800UF/25V OPTION C OPTION F OPTION B CP4006 TO CN4006 * MODEL / AREA OPTION MODEL AVR4 AVR3 SR5009 AREA E3/E2/E1/E1C/K U/N/K OPTION A OPTION B OPTION C...
RS232 PART RS_CNT PART (SR5009) (SR5009) TO CN4701 CP4700 INPUT 1/1 C1 SR5009 ONLY AVR2E3 : 7P SR_5009 : 11P CP4703 SR5009 ONLY HDAM 1/1 A1 TO CN4703-2 RS232 PART RS_CNT PART SCHEMATIC DIAGRAMS (28/32) 28-MAIN_RS232-CNT GND LINE POWER+ LINE POWER- LINE COMPONENT ( Y ) ANALOG AUDIO...
G x4 A X25 A X4 J X2 HDMI JACK/TUNER PACK/M3/BRACKET/MX JACK K X23 F X2 3 X2 2 MARANTZ A X2 20X2 C X2 23 X4 SR5009 ALL 22 X4 WARNING: Parts marked with this symbol z have critical characteristics.
PACKING VIEW Please see the last chapter for the part list. *MANUAL POLYBAG ASSY* ZIPPER BAG (A4size) Notes on RADIO ( ALL ) SAFETY INST. ( ALL ) GOST SHEET ( N Only ) JAPAN ADRESS SHEET (F Only) JAPAN POST CARD (F Only) WARRANTY ( U Only ) SPK WIRE LABEL ( ALL ) UK plug...
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F56108VNFP (HDMI : U1018) PE0/D8 PC4/A20 PD7/D7 PC5/A21/SCK5/CS5#-D PD6/D6 PC6/A22/RxD5/CS6#-D PD5/D5 PC7/A23/TxD5/CS4#-D/CS7#-D PD4/D4...
Page 145
Pin Name Symbol Pu/Pd STBY STOP Function STBY REMOTE 232C POWER SUPPLY (REMOTE 3.3V) POWER(232C) 18 P85 control pin.(ON: H) (SR5009 only) (SR5009)/ NC(NR1605) 19 RES# RESET Reset input (reset: L) 20 XTAL XTAL Oscillator connection 21 VSS 22 EXTAL EXTAL Oscillator connection 23 VCC...
Page 146
Pin Name Symbol Pu/Pd STBY STOP Function STBY 58 P82/TRCLK FL CE VFD control pin 59 VCC +3.3V 60 P81/TRSYNC FL RST VFD control pin ZVOL DATA(X2100/ 61 P80 ZONE VOLUME control pin SR5009/NR1605)/ NC(E900) BCLK/P53(INPUT only) 63 P52/RD# ZVOL CLK ZONE VOLUME control pin 64 P51/WR1#/BC1# ZONE VOLUME control pin...
Page 147
Pin Name Symbol Pu/Pd STBY STOP Function STBY PA1/A1/PO17/ CLK MUTE A.PLD MUTE control pin (MUTE Active="H") TIOCA6/TIOCB6 PA0/A0/BC0#/PO16/ PRE MUTE PRE OUT MUTE control pin TIOCA6 ETHERNET communication control pin(Factory 102 PE7/IRQ7-A/D15 E FACT RST Reset) 103 PE6/IRQ6-A/D14 104 PE5/IRQ5-A/D13 REQ SOMI MAIN-SUB ucom communication control pin Input Selector rotation detection pin(Rotary...
Page 148
RX210 Group 1. Overview R5F5210ABDFP (HDMI : U1020) RX210 Group PLQP0100KB-A (100-pin LQFP) (Top view) VREFL0 VREFH0 AVCC0 AVSS0 R5F5210ABDFP Terminal Functions Note: • This figure indicates the power supply pins and I/O port pins. For the pin configuration, see the table “List of Pins and Pin Functions (100-Pin LQFP)”.
Page 149
Symbol Pin Name Pu/Pd STBY Function LvCnv STBY 34 P12/SCL/IRQ2 778_1_RST HDMI MN8647781(TX) RESET control pin ※ 35 PH3 HSDA HDMI I2C- MN8647781 3VPu 36 PH2/IRQ1 HSCL HDMI I2C- MN8647781 3VPu 37 PH1/IRQ0 778_1_HINT HDMI MN8647781(TX) HDMI INT input pin 38 PH0 778_2_RST HDMI MN8647781(RX) RESET control pin...
Page 150
Symbol Pin Name Pu/Pd STBY Function LvCnv STBY 85 PD1/IRQ1 DSP1CS DSP control pin (ADSP21487KSWZ-3B) 3VPu 86 PD0/IRQ0 DSP1FLAG0 DSP control pin (ADSP21487KSWZ-3B) 87 P47/AN007 88 P46/AN006 VIN A COMPOSITE VIDEO SELECT IC(NJM2595) 89 P45/AN005 VIN B COMPOSITE VIDEO SELECT IC(NJM2595) 90 P44/AN004 VIN C COMPOSITE VIDEO SELECT IC(NJM2595)
Page 153
DESCRIPTION NAME TOLERANT Reset Input, active low(2) (4) RXIN1 Biphase signal, input 1, built-in coaxial amplifier VDDRX – – Power supply, 3.3 V (typ.), for RXIN0 and RXIN1. RXIN0 Biphase signal, input 0, built-in coaxial amplifier GNDRX Ground, for RXIN Oscillation circuit input for crystal resonator or external XTI clock source input(5) Oscillation circuit output for crystal resonator AGND...
Page 154
ADSP21487KSWZ3B (HDMI : U1024) PIN 1 GND PAD (PIN 177) at BOTTOM TOP VIEW (PINS DOWN) ADSP21487KSWZ3B Terminal Function Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. SDDQM DAI_P10 DPI_P08 FLAG0 SDCKE DPI_P07 FLAG1 DAI_P20...
Page 155
W9864G6JH-6 (HDMI : U1023) W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 156
W9864G6JH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 157
PCM1690 (HDMI : U1048) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — —...
Page 158
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 — — — Reserved, tied to analog ground AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 159
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (HDMI:U1052) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 161
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 11-Input selector And Tone control PIN DESCRIPTION R2A15218FP Pin Function PIN No. Function Name 23,21, FROUT,FLOUT, 17,15, COUT,SWOUT, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel 11,9, SROUT, SLOUT, SBROUT,SBLOUT 24,20, FRC,FLC, 18,14, CC,SWC, Connects capacitor for reducing click noise of 12,8, SRC,SLC, L/R/C/SW/SL/SR/SBL/SBR channel volume...
Page 162
GENERAL DESCRIPTION PACKAGE OUTLINE The NJM2595 is a 5-input 3-output video switch. Its switches select one from five signals received from VTR,TV,DVD, TV-GAME and others. BD3812F (INPUT:IC5202) The NJM2595 is designed for audio items, such as AV amplifier and others. NJM2595D NJM2595M 14 OUT1 IN 1...
Page 164
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 165
MAIN REF No. Part No. Part Name Remarks Q'ty New Ver C4020 C,FILM POLYESTER MI-0047UF-J/50V-5RE D020473167050S C4021 C,CERAMIC CHIP HIK X7R)2200PF-K/50V-1608REEL D011222777160S C4023-4025 C,FILM POLYESTER MI-0047UF-J/50V-5RE D020473167050S C4027 C,CERAMIC CHIP HIK X7R)1000PF-K/50V-1608REEL U, K D011102777160S C4027 X7R)0.1UF-K/50V-1608REEL D011104577160S C4028 C,FILM POLYESTER MI-0047UF-J/50V-5RE D020473167050S C4030 C,FILM POLYESTER MI-0047UF-J/50V-5RE...
Page 166
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 168
VIDEO VIDEO PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 169
VIDEO REF No. Part No. Part Name Remarks Q'ty New Ver CP3404 CN,WAFER 1.25B-2-17A 17P BtoB HEADER(MALE) P=1.25MM L109125321710S CP4605 CN,WAFER 1.25B-2-17A 17P BtoB HEADER(MALE) P=1.25MM L109125321710S CP5000 CN,WAFER 1.25B-2-11A 11P BtoB HEADER(MALE) P=1.25MM L109125321110S CP5001 CN,WAFER 1.25B-2-13A 13P BtoB HEADER(MALE) P=1.25MM L109125321310S CP5003 CN.WAFER 2.5MM YMAW025-08R DIP RA...
Page 170
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 171
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver C2139,2140 00D2570507976 C,CERAMIC CHIP T.C CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2141 00D9630333203 C,ELECT GE 85C 100UF-M/16V,5*11-5RE,SHL SY D040101083090S C2142 00D2570507976 C,CERAMIC CHIP T.C CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2145 00D9630333203 C,ELECT GE 85C 100UF-M/16V,5*11-5RE,SHL SY D040101083090S C2146 00D2570505910...
Page 172
SMPS SMPS PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 173
7CH_AMP 7CH_AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 174
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R455 R,CARBON FILM 15K-J,1/5W-52RE-AX C00001536P520S R456,457 R,CARBON FILM 10K-J,1/5W-52RE-AX C00001036P520S R458 963125012630S R,METAL FILM 100PPM 22-J,1W-5REEL C060022065050S R459 R,CARBON FILM 22K-J,1/5W-52RE-AX C00002236P520S R460 R,CHIP THICK 180K-J,1/16W-1608REEL C20001846M160S R461 963125010690S R,METAL FILM 100PPM 15K-J,2W-R.REEL C060015366050S R462...
Page 175
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R580 963252100150S POSISTOR DHPTHF1608 471P 115T SMD PTC THERMISTOR F320471001150S R582 R,CARBON FILM 150K-J,1/5W-52RE-AX C00001546P520S R583 CN,WIRE 1P JUMPER (0.6/52MM) L045084006040S R584 R,CARBON FILM 680K-J,1/5W-52RE-AX C00006846P520S R585 R,CARBON FILM 15K-J,1/5W-52RE-AX C00001536P520S R586,587 R,CHIP THICK 10K-J,1/16W-1608REEL...
Page 176
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R710-716 CN,WIRE 1P JUMPER (0.6/52MM) L045084006040S R717-723 R,CARBON FILM 220-J,1/5W-52RE-AX C00002216P520S R724-730 R,CHIP THICK 56K-J,1/16W-1608REEL C20005636M160S R731,732 R,CHIP THICK 2.2K-J,1/16W-1608REEL C20002226M160S CAPACIITORS GROUP C401 C,CERAMIC CHIP HIK X7R)0.1UF-K/50V-1608REEL D011104577160S C403 C,CERAMIC CHIP T.C X7R)0.01UF-K/50V-1608REEL D010103777160S...
Page 177
HDMI HDMI PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 178
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver U1055 963236101220D IC,LOGIC ADV7850 HDMI 1.4A RECEIVER BGA425 J040785005510S U1061-1070 963239101370S IC,LOGIC-D/D CONVER EN5339QI 3A BUCK PWM DC-DC QFN24P J048533900010S U6000 943639101380D MODULE iBT-06-02S BT MODULE CLASS2 V2.1+EDR HCI INTERFACE E100070060020S U6001 963239101380S...
Page 179
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1189 R,CHIP THICK 47K-J,1/16W-1005REEL C20004736M101S R1190,1191 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1192 R,CHIP THICK 47K-J,1/16W-1005REEL C20004736M101S R1194,1195 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1197,1198 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1199 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1201 R,CHIP THICK 33-J,1/16W-1005REEL...
Page 180
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1496 R,CHIP THICK 27K-J,1/16W-1005REEL C20002736M101S R1497 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1498 R,CHIP THICK 220K-J,1/16W-1005REEL C20002246M101S R1499 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1500 R,CHIP THICK 3.3K-J,1/16W-1005REEL C20003326M101S R1501 R,CHIP THICK 100K-J,1/16W-1005REEL C20001046M101S R1502,1503 R,CHIP THICK 10K-J,1/16W-1005REEL...
Page 187
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver C2236,2237 C,CERAMIC CHIP HIK X7R)0.01UF-K/25V-1005REEL D011103174101S C2240-2243 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C2244-2246 C,CERAMIC CHIP HIK X7R)0.01UF-K/25V-1005REEL D011103174101S C2247 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C2248,2249 C,CERAMIC CHIP HIK X7R)0.01UF-K/25V-1005REEL D011103174101S C2250,2251 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL...
Page 188
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver X1006,1007 963141101180S CRYSTAL CHIP 27.000MHz CL=7PF FA-238/SMD3225 EPSON E80527R000050S X1008 963141100770S CRYSTAL CHIP 24.576MHz CL=10PF FA-238/SMD3225 EPSON E80524R576050S X1009 963141101180S CRYSTAL CHIP 27.000MHz CL=7PF FA-238/SMD3225 EPSON E80527R000050S X6000 963141101190S CRYSTAL CHIP 32.768KHz CL=12.5PF FC-135/SMD3215 EPSON E80532R768260S Z1001...
Page 189
HDAM HDAM PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 190
HDAM REF No. Part No. Part Name Remarks Q'ty New Ver R4257 R,CHIP THICK 150-J,1/16W-1608REEL C20001516M160S R4258-4260 R,CHIP THICK 22-J,1/16W-1608REEL C20002206M160S R4261,4262 R,CHIP THICK 1M-J,1/16W-1608REEL C20001056M160S R4263,4264 R,CHIP THICK 33K-J,1/16W-1608REEL C20003336M160S R4265,4266 R,CHIP THICK 22-J,1/16W-1608REEL C20002206M160S R4267,4268 R,CHIP THICK 5.6K-J,1/16W-1608REEL C20005626M160S R4269,4270 R,CHIP THICK 330-J,1/16W-1608REEL...
Page 191
PREOUT PREOUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 192
CX870_MID CX870_MID PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed b NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model BK : Black model SG : Silver gold model REF No.
Page 193
BADGE NR1501FB(MARANTZ) SILVER/GRAY 11c AL 5630210678000S 943424100270M DECORATION RING SR-5006(U1B) ABS BK(CGR1A526B37) A3 5127210981000S 943424100280M DECORATION RING SR-5006 SG 5127210981100S 00M10BW355010 LENS POWER SR5005U1B(MARANTZ)(CGL1A231) PMMA HI-855M A4 3710211083000S 411510021005M BUTTON POWER NR1501FB(MARANTZ) ABS BK HF380-9001 TACT 5090213961000S 963411012000M BUTTON POWER NR1501SG 5097213961100S...