Table of Contents
Advertisement
2. Auto Presetting
This function automatically scans the LW, MW and FM band and
enters all stations with proper signal strength into the memory.
This function is available only for SR-14EX.
Select the FM band with the BAND button y.
1.
2.
Tune in the lowest receivable frequency.
While pressing the MEMO button i, turn the GYRO TUNING
3.
knob @1 to up. Auto memory starts at this point.
4.
"MEMO " will blink on the display.
5.
Each time the tuner finds a station, the scanning will pause and
the station will be played for five seconds. During this time, the
following operations are possible:
1) The band can be changed using the BAND button y.
2) The mode can be changed using the FM MODE button u.
6.
If no button is pressed during this period, the current frequency is
preset in location CH-2. If you wish to skip the current station,
turn the GYRO TUNING knob @1 during this period, the current
frequency is skipped and auto presetting continues.
7.
Operation stops automatically when all 50 preset memory
positions are filled or when auto scanning attains the highest end
of all bands. To stop the auto preset function at anytime, press
the CL (CLEAR) button o.
3. Recalling a Preset Station
Press the PRESET button !8 to change the display to preset.
1.
2.
Select the desired preset station by turning GYRO TUNING knob
@1 on the front panel or press ^ Skip
mode on the remote.
Note;
• Direct selection method using the ten keypad on the remote,
select the desired preset station by entering one or two digits
using the ten keypad on page of keypad mode on the remote.
• To return to the Manual Tuning mode, press the AUTO TUNING
button !7 .
4. Preset Scan Tuning (Using the remote control unit)
1.
Press the Preset Scan on page of Tune mode on the remote. "P-
SCAN" indicator blinks in the display. (The preset station with the
smallest preset number is recalled first. If no stations have been
preset, CH "00" blinks in the display and the unit returns to the
previous mode.)
2.
Preset stations are recalled in sequence (CH-1 › CH-2, etc.) for 5
seconds each. Preset numbers that do not contain stations are
skipped.
3.
You can fast forward the preset stations by pressing the Skip ^
button continuously. When the desired preset station is received,
cancel the preset scan operation by pressing the Skip
the Preset Scan button or Clear button.
5. Clearing Preset Stations
You can remove preset stations from memory using the following
procedure.
1.
Recall the preset number to be cleared with the method
described in "Recalling" a preset station .
Press the MEMO button i on the front panel or Memo button on
2.
page of Tune mode on the remote unit, "MEMO" blinks in the display
for 5 seconds. While "MEMO" is still blinking, press the CL (CLEAR)
button o on the front panel or Clear button on page of Tune mode
on the remote unit. "CLEAR" appears on the display to indicate that
the specified preset number has been cleared.
button on page of Tune
v
button or
v
21
STATION NAME PRESET
The station name preset function allows the name of each preset
channel to be entered using alphanumeric characters. The Station
Name button is valid only in the tuner mode. Before station name
preset operation, store stations with the preset memory operation.
Press the MEMO button i on the front panel or Memo button on
1.
page of Tune mode on the remote for more than 3 seconds.
2.
The left most column of the station name indicator flashes,
indicating the character entry ready status.
[Operation (Using the SR-14EX)]
When the GYRO TUNING knob @2 is turned, alphabetic and
3.
numeric characters will be displayed in the following order:
A
B
C ...Z
1
2
UP
DOWN
4.
After selecting the first character to be entered, press the MEMO
button i. The entry in this column is fixed and the next column
starts to flash. Fill the next column and press the MEMO button
i for more than 1 second to confirm the entry.
Note:
Unused columns should be filled by entering blanks.
[Operation (Using the remote unit)]
3.
Enter the character using the ten keypad on page of Keypd
mode. For example, to enter "A":
1) Press the "1" button. "A" appears on the display column.
2) Every time the 1 button is pressed, the displayed character
changes in the order: A
Pressing buttons other than the "1" button cause different
characters to be displayed in a similar way, so that other
alphanumeric characters can be entered. To enter a blank or
space, press the "9" button.
4.
When the desired character is displayed, press the Memo button
on page of Keypad mode to confirm the entry in this column and
move to the next column. After having filled all of the 8 columns,
press the Memo button, or more than 1 second to confirm the
entry.
DIRECT FREQUENCY CALL
1.
Press the F/P button on page of Keypad mode on the remote.
2.
Front display will show "FREQ ----".
3.
Input your desired frequency with Ten keypad button on the
remote.
PLAYBACK OPERATION
NORMAL PLAYBACK
Press the POWER ON button on the remote.
1.
Turn the INPUT SELECTOR !5 on the front panel or press the
2.
FUNCTION buttons on page of Input mode on the remote unit to
select an input source.
Press the Surround mode buttons e on the front panel or
3.
desired surround mode buttons page of Surround mode on the
remote unit to select.
Adjust the volume level using the VOLUME knob !6 on the front
4.
panel or press the VOLUME + / – buttons on the remote. If
necessary, adjust the tone using the Bass and Treble buttons on
page of Tone mode on the remote unit.
LISTENING TO A DIFFERENT AUDIO SOURCE WHILE
WATCHING A VIDEO SOURCE (Using the remote control
unit)
1.
Select one of the following video sources TV, LD, DVD, VCR1,
DSS/VCR2 or AUX.
2.
Next, select one of the following audio sources FM, AM, CD,
TAPE, or CDR/MD.
3..... 0
–
+
/
(Blank)
B
C
1
A...
A
Hide quick links:
Advertisement
Table of Contents
