Husqvarna AUTOMOWER 405X Operator's Manual page 23

4. Push the BACK button.
3.12.5 Security level
There are 3 security levels for the product.
Function Low
PIN code
STOP button
pressed
Carried away
PIN-code - The correct PIN-code must be entered
•
to get access to the menu structure of the product.
If the incorrect PIN-code is entered 5 times, the
product is locked for a time. The lock is extended
for each new incorrect try.
STOP button pressed - The alarm goes off if the
•
STOP button has been pushed and the PIN code
is not entered in less than 30 seconds.
Carried away - The alarm goes off if the product is
•
lifted.
3.12.5.1 To set the security level
Select 1 of 3 security levels for your product.
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 21 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Security level .
3. Use the arrow buttons and the OK button to select
the level of security.
4. Push the OK button.
3.12.5.2 To create a New loop signal
The loop signal is randomly selected to create a unique
link between the product and the charging station. In
rare cases, there may be a need to generate a new
signal, for instance if two adjacent installations have a
very similar signal.
1. Place the product in the charging station.
To get access to the menu in the
2. Do steps 1–3 in
display of the product on page 21 .
3. Use the arrow buttons and the OK button to move
through the menu structure
New loop signal .
4. Await confirmation that the loop signal has been
generated. This normally takes about 10 seconds.
3.12.5.3 To change the PIN-code
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 21 .
1650 - 005 - 17.03.2022
2.
3.
4.
5.
6.
7.
Medium High
3.12.5.4 To change the duration of the alarm
X X
1.
X
2.
X
3.
4.
3.12.6 Messages
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
Refer to
If the product is disrupted in any way, for example it
is trapped or the battery is low, a message is saved
relating to the disruption and the time it happened.
Settings > Security >
If the same message is repeated several times, this
may indicate that an adjustment to the installation or the
product is required. Refer to
3.12.6.1 To read the messages
1.
2.
3.
3.12.7 Weather timer
Security > Advanced >
Weather timer automatically adjust the cutting time to
the growth of the grass. The product is not permitted to
operate more than the schedule settings.
Use the arrow buttons and the OK button to move
through the menu structure Settings > Security >
Advanced > Change PIN-code .
Enter the new PIN code.
Push the OK button.
Enter the new PIN code again.
Push the OK button.
Make a note of the new PIN code. Refer to
Introduction on page 3 .
Do steps 1–3 in To get access to the menu in the
display of the product on page 21 .
Use the arrow buttons and the OK button to move
Security > Advanced >
through the menu structure
Duration > Duration of alarm .
Use the arrow buttons to select a time interval of 1
to 20 minutes.
Push the BACK button.
Troubleshooting on page 36 .
Installation on page 13 .
To get access to the menu in the
Do steps 1–3 in
display of the product on page 21 .
Use the arrow buttons and the OK button to move
through the menu structure Messages > Fault
messages and Messages > Info messages .
Read the messages and read the
to get information and recommendations to correct
the faults.
Troubleshooting
Installation - 23