Hopper Operation; Operating Characteristics - Toro Groundsmaster 200 Series Installation Instructions Manual

Operation
Note: Determine the left and right sides of the machine
from the normal operating position.
Before Operating Hopper
1. Start engine. Raise and lower hopper several times.
(move control valve lever forward to lower hopper and
in reverse direction to raise hopper)
2. Check interlock switch operation as follows:
Raise the hopper and engage the PTO switch while the
engine is running. The engine should stop within 2
seconds. If engine stops, the switch is operating
correctly; thus, proceed to next step. If engine does not
stop, there is a malfunction in the interlock system.
Raise the hopper and depress the traction pedal while
engine is running the PTO lever is disengaged. The
engine should stop within 2 seconds. If engine stops, the
switch is operating correctly; thus, continue operation.
If engine does not stop, there is a malfunction in the
interlock system.
3. Stop engine. Check for hydraulic leaks. Check
hydraulic fluid level in front axle and replenish as
necessary. (Refer to Traction Unit Operator's Manual
for specifications).

Hopper Operation

(When used with a 52" or 62" Blower Kit)
1. Move control valve lever forward to lower hopper and
in reverse direction to raise hopper.

Operating Characteristics

Caution
When grass collector is removed, NEVER
operate without deflector in place.
For best performance, regulate traction pedal to keep
engine rpm high and somewhat constant. A good rule to
follow is: decrease ground speed as the load on the cutting
blade increases; and increase ground speed as the load on
the blade decreases. This allows the engine, working with
the transmission, to sense the proper ground speed while
maintaining high blade tip speed necessary for good
quality–of–cut, vacuuming action, and to throw grass into
hopper If blower speed drops too low, plugging may result
Refer to Cutting Unit and Traction Unit Operator's Manual
for operation of each.
Caution
Use care to avoid collision between hopper
and any stationary objects Always trim with
left side of cutting unit.
1. Inflate all tires on traction unit to 18–20 psi.
2. This grass collector is designed for use in wet or dry
conditions. Do not collect extremely long grass as the
hopper will fill too quickly.
3. When collecting wet, heavy grass, some clippings may
not be thrown completely through the chute. The hole in
the bottom of the chute allows these clippings to drop
out without plugging the chute. When this happens,
reduce ground speed.
Caution
Never place hands or feet in chute, blower, or
cutting unit.
4. The bumper which protects the blower housing doesn't
extend far enough to eliminate the chance of the hopper
or hopper frame striking a stationary object. Stay far
enough away from obstructions to avoid collisions.
Trim with left side of cutting unit only.
5. While operating, check frequently for excessive
clippings left on turf or uncut grass. If those conditions
occur, the blower or cutting unit may be plugged. Stop
unit, disengage PTO, set brake and shut off ignition.
Check for obstructions in the chute, blower or cutting
unit. Clear any obstruction using a stick or similar tool.
Check blower belt tension. If slipping, readjust.
6. The grass collector hopper is designed to exhaust air
beside the chute. This allows the hopper to fill
completely without decreasing performance. Grass will
fall through the opening in the front of the hopper when
hopper is full. Immediately disengage the power take
off and empty the hopper.
7. Cut grass often, especially when turf growth is rapid. If
shorter turf is desired, cut the grass again. Overlap the
swaths to produce an even cutting pattern.
Important When transporting, hopper must be in down
position with rear cover latched over large cover.
Hopper & Frame Removal
1. Stop unit, disengage PTO, set brake and shut off
ignition.
2. Move hopper control valve lever forward and reverse a
few times to release pressure in hydraulic system.
16