Summary of Contents for Follett Horizon Elite HCD710APS
Page 1
Horizon Elite Ice Machine Models with RIDE Technology ™ ™ Installation Instructions for Cornelius PR150 HCD710APS, HCC1010APS, HCC1410APS, HCC1010WPS, HCC1410WPS, (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 •...
Page 2
Chewblet Ice Machine Model Number Configurations ® 1810 Application Configuration Icemaker Voltage Series Condenser MC Maestro™ C 208-230/60/1 (icemaking head) 425 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 425 lbs Chewblet ® W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (193 kg)
Page 3
Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Docking assembly Ice transport tube External connection Internal connection Front cover Cornelius • RIDE Technology self-contained...
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➋ ➌ ➊ ➎ ➍ 7/16" DO NOT TILT ICE MACHINE TO ACCESS BOLTS! COMPRESSOR DAMAGE 7/16" WILL RESULT ➐ ➏ Cornelius • RIDE Technology...
• 10-70 psi (69-483kpa) • 45 to 90 F (7 to 32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) • This equipment is to be installed with adequate backflow protection to comply with applicable...
Dispenser preparation Prepare the dispenser. ➋ ➋ ➊ ➊ • Coil capillary tube and secure away from bin • ➊ Remove ice entry cover plate ➊ fill opening • Remove bin thermostat capillary tube from ➋ bracket ➊ ➊ ➋ ➋...
Page 7
➋ ➌ ➊ ➊ ➋ • • I Mount cover plate/transport tube assembly nsert end of ice transport tube (with retaining on outside of dispenser using screws, flat holes) through hole in center of cover plate ➊ ➋ ➊ washers , lock washers and nuts assembly...
3.10 ➊ ➊ ➋ • • Route thermostat capillary tube through Insulate entire length of ice transport tube ➊ ➊ mounting bracket grommets as shown and route to icemaker in accordance with directions in Horizon installation instructions • ➋ Route bin signal wire to icemaker BEFORE PROCEEDING Prior to installing the docking assembly, ensure that the drain fitting is oriented (right...
Page 9
Docking assembly Install the docking assembly. WARNING • Docking station must be secured in accordance with these instructions to ensure ice machine stability. • Ventilation openings in the docking station should be clear of obstruction Wall bracket accessory Machine stand accessory •...
Page 10
Undercounter installation detail Front View Top View Access panel/ door on counter ➌ ➊ 2" (51 mm) 1010/1410: 2.25" (57 mm) ➍ 710: 2" (51 mm) bottom of ice machine side of ice machine 1010/1410: 2" (51 mm) 710: 3.25" (82.55 mm) CAUTION •...
Ice transport tube Install the ice transport tube. Ice transport tube installation. ➋ Hot Water 160 F (71 C) ➎ ➊ 1/4" ➌ ➍ ➏ ➐ Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋...
Page 12
Bin signal Install the bin signal. Bin Signal Installation ➏ ➎ ➐ Ground ➌ ➊ 16" ➋ (61 cm) ❹ • Mount the electrical box to the side of the dispenser ➊ to establish a ground connection. Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an appropriate ground.
External connections Connect utilities to docking assembly. Air-cooled ice machines only Water-cooled ice machines only ➊ ➊ ➋ ➏ ➋ ➐ ➌ ➌ Minimum 8" ➏ Minimum 8" ➑ radius radius 2 ft. x 1" OD 2 ft. x 1" OD silicone tubing silicone tubing 3/4"...
Page 14
Chassis drain plumbing - required • Plug must be removed from John Guest fitting. • Route 3/8" drain tubing through knockout in back of docking station and insert fully into John Guest fitting connection at the rear of the machine chassis. Route other end of 3/8"...
Internal connections Connect docking assembly to ice machine. CAUTION • Plug must be accessible after final installation. Air-cooled ice machines – follow steps 8.1 through 8.5. Water solenoid, shut-off valve, Ice transport tube and potable water line options If water solenoid is already mounted to evaporator: •...
Page 16
Water-cooled ice machines – follow steps 8.6 through 8.12. TDS switch Cooling lines HIGH CLEAN • Set the TDS switch on the electrical box: • Install ice machine cooling water lines to HIGH: for extended service life docking assembly LOW: for low-scale water Ice transport tube Water solenoid, shut-off valve, and potable water line options...
Page 17
8.10 Power cord Cooling lines and power ➋ ➊ • Remove twist tie • Carefully pass cord through opening and • Connect cooling water lines to ice plug into wall outlet machine ➊ • For H_E units, install a suitable plug •...
Front cover Install front cover to ice machine. Install front cover Front cover installation – air-cooled undercounter only ➊ ➋ ➋ ➌ ➊ ➌ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of docking assembly ➊...
Page 19
Long tube run recommendations max. 2 ft (.6m) ➊ ➋ 1/4" • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.6m) to prevent dips or traps ➋...