Table of Contents
Advertisement
Quick Links
Horizon Elite
HCD/HMD710AVS, HCC/HMC/HCE/HME1010AVS, HCC/HMC/HCE/HME1410AVS,
HCC/HMC/HCE/HME1010WVS, HCC/HMC/HCE/HME1410WVS,
(See model number configurator on page 2 for details.)
Order parts online
www.follettice.com
Ice Machine Models with RIDE
™
Installation Instructions for Vision
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Technology
™
™
self-contained
01113208R02
Advertisement
Table of Contents
Related Manuals for Follett Horizon Chewblet 710 Series
Summary of Contents for Follett Horizon Chewblet 710 Series
- Page 1 Horizon Elite Ice Machine Models with RIDE Technology ™ ™ Installation Instructions for Vision ™ HCD/HMD710AVS, HCC/HMC/HCE/HME1010AVS, HCC/HMC/HCE/HME1410AVS, HCC/HMC/HCE/HME1010WVS, HCC/HMC/HCE/HME1410WVS, (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 •...
- Page 2 Chewblet Ice Machine Model Number Configurations ® 1810 Application Configuration Icemaker Voltage Series Condenser MC Maestro™ C 208-230/60/1 (icemaking head) 425 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 425 lbs Chewblet ® W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (193 kg)
- Page 3 Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly Ice transport tube External connection Internal connection Front cover VISION • RIDE Technology self-contained...
-
Page 4: Unpack Ice Machine
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➋ ➌ ➊ ➎ ➍ 7/16" DO NOT TILT ICE MACHINE TO ACCESS BOLTS! COMPRESSOR DAMAGE 7/16" WILL RESULT ➐ ➏ VISION • RIDE Technology... -
Page 5: Prepare The Installation Site
• 10-70 psi (69-483kpa) • 45 to 90 F (7 to 32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) • This equipment is to be installed with adequate backflow protection to comply with applicable... -
Page 6: Dispenser Preparation
Dispenser preparation Prepare the dispenser. Bin Signal Installation ➏ ➎ ➐ ➋ Ground ➌ ➊ 24" (610 mm) ➌ • Mount the electrical box to the side of the Vision dispenser ➊ to establish a ground connection. Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an appropriate ground. -
Page 7: Before Proceeding
Louvered docking assembly Install the louvered docking assembly. BEFORE PROCEEDING Prior to installing the louvered docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation. An optional straight drain fitting is also supplied. You may need to remove the back panel of the docking assembly in order to re-orient or change the drain fitting. - Page 8 Undercounter installation detail Front View Top View Access panel/ door on counter ➌ ➊ 2" 2" (51 mm) 2.25" (51 mm) (57 mm) ➍ 24" x 15" cutout (610 mm x 381 mm) bottom of ice machine side of ice machine CAUTION •...
-
Page 9: Ice Transport Tube Installation
Ice transport tube Install the ice transport tube. Ice transport tube installation. Hot Water 160 F (71 C) 1/4" Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 19. - Page 10 Dispenser ice transport tube installation Ice tube retainer bracket 1" (25mm) ice tube retaining bracket ice tube ice tube Front View Front View VU155 VU300 ice tube retaining bracket thermostat thermostat ice tube retaining bracket tabs in ice tube tabs in ice tube ice tube retainer bracket retainer bracket...
-
Page 11: External Connections
External connections Connect utilities to louvered docking assembly. Air-cooled ice machines only Water-cooled ice machines only ➊ ➊ ➏ ➋ ➋ ➐ ➌ ➌ Minimum 8" ➑ Minimum 8" ➏ radius radius 2 ft. x 1" OD 2 ft. x 1" OD silicone tubing silicone tubing 3/4"... -
Page 12: Internal Connections
Internal connections Connect louvered docking assembly to ice machine. CAUTION • Plug must be accessible after final installation. • H_E1410A/W 230/50/1) requires a 20 amp circuit (4.00 mm wire) Air-cooled ice machines – follow steps 7.1 through 7.5. Ice transport tube Potable water and drain lines ➋... -
Page 13: Tds Switch
Water-cooled ice machines – follow steps 7.6 through 7.12. TDS switch Cooling lines HIGH CLEAN • Set the TDS switch on the electrical box: • Install ice machine cooling water lines to louvered docking assembly HIGH: for extended service life LOW: for low-scale water Potable water and drain lines Ice transport tube... - Page 14 Cooling lines and power 7.10 Power cord ➋ ➊ • Remove twist tie • Carefully pass cord thru opening and plug • Connect cooling water lines to ice into wall outlet machine ➊ • For H_E units, install a suitable plug •...
-
Page 15: Front Cover
Front cover Install front cover to ice machine. Install front cover Front cover installation – air-cooled undercounter only ➊ ➋ ➋ ➌ ➊ ➌ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊... - Page 16 • Secure insulated ice transport tube at least every 2 ft (.6m) to prevent dips or traps ➋ Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett LLC. Chewblet is a registered trademark of Follett LLC, registered in the US.