Page 1
™ ™ Horizon Ice Machines with RIDE Technology ™ Installation Instructions for Harmony H_C700AHS, H_C700WHS, H_D700AHS, H_D700WHS, H_E700AHS, H_E700WHS (See model number confi gurator on page 2 for details.) Order parts online www.follettice.com self-contained Horizon Satellite-fi ll icemakers fi t most countertop dispensers manufactured by Cornelius •...
Page 2
Horizon Series Ice Machine Model Number Configurations Icemaker Voltage Series Condenser Application Configuration HC Horizon C 208-230/60/1 up to Air-cooled, self-contained V Vision™ S RIDE™ (self-contained only) Chewblet ® 750 lbs W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 self-contained (340kg) HM Horizon ice delivery...
Page 3
Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly Ice transport tube External connection Internal connection Front cover HARMONY • RIDE Technology self-contained...
Page 4
Unpack Carefully unpack and inspect the contents of your Follett icemaker. Unpack icemaker 7/16" 7/16" HARMONY • RIDE Technology self-contained...
Site preparation Prepare the installation site. Provide drainage, water supply and electrical power to within 6 feet (2m) of icemaker in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. Installation site requirements H_D700A/W NEMA 6-15 H_D700A/W...
Dispenser preparation Prepare the dispenser. Top preparation Top preparation 5" (127mm) 3" ∅ (76,2mm) • Remove protective tape from gaskets • Locate hole position 5" (127mm) from back of dispenser top • Cut 3" (77,2mm) diameter hole in dispenser top Top preparation Top preparation ➋...
Page 7
Agitation adjust. – CORNELIUS Cornelius models ED, DB, DF, IDC and FLAVOR FUSION Adjust the agitation timer located on the Cornelius PC board to 1 second on, 1 hour off. Note: See Cornelius manual for more information. Agitation adjustments – LANCER 4500 SERIES ROCKER PRESS IN ON PRESS IN ON...
Page 8
Agitation adjustments – LANCER FS SERIES Initialization Screen (Boot Up Only) Lancer FS-16 Ver. 0.200 ➊ Main Menu Sub-Catagory FS-16 Setup Brands Per Side Major/Minor V:1 L:2 R:1 FS-16 Setup Bonus Key Setup Config Bonus Key V:1 T:F M:S B:W FS-16 Setup Soda/Plain Water Cancel...
Page 9
Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES storage bin ➊ gate gate restrictor mounting plate plate ➋ ice diverter (supplied) gasket ice chute flange extends into storage bin through gate opening flat washer apply food-grade silicone sealant 10-32 nut to this surface to seal to bin gate...
Page 10
3.10 Restrictor plate adjustment – CORNELIUS IDC and FLAVOR FUSION ➋ adjust restrictor plate to fully open position ➊ Cornelius IDC and Flavor Fusion These dispensers require the adjustment of the ice restrictor plate. ➊ • Loosen four nuts on ice chute assembly ➋...
Page 11
Louvered docking assembly Install the louvered docking assembly. WARNING • Docking station must be secured in accordance with these instructions to ensure icemaker stability. • Ventilation openings in the louvered docking station should be clear of obstruction. Failure to do so could result in damage to equipment.
Page 12
Undercounter installation detail – Horizon 700 series Front View Top View Access panel/ CROSSBRACE door on counter ➌ ➊ 3.25" (82.55mm) 2" 2" (50mm) (50mm) ➍ bottom of ice machine side of ice machine CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. Failure to do so could result in damage to equipment.
Page 13
Undercounter installation detail – Horizon 700 series (continued) Horizon ice machines can be installed undercounter/in-cabinet to fi ll bins or dispensers using RIDE technology. Care must be taken to ensure proper cabinet venting to avoid recirculation of hot air. Improper venting can cause ice machine out- ages.
Ice transport tube Install the ice transport tube. Ice transport tube installation. Hot Water 160 F (71 C) 1/4" Ice transport tube tips ➊ • Insulate entire length of ice transport tube ➋ • Secure ice transport tube as needed to prevent dips and traps from forming. For long tube runs see guide on page 19.
External connections Connect utilities to louvered docking assembly. Air-cooled icemakers only Water-cooled icemakers only ➋ ➍ ➋ ➌ ➊ ➊ • Remove access panel if necessary • Remove access panel if necessary ➊. ➊ • Install drain line • Install drain line The rigid drain line from the icemaker The rigid drain line from the icemaker must be vented and have at least 1/4"...
Internal connections Connect louvered docking assembly to icemaker. CAUTION • Plug must be accessible after fi nal installation. Air-cooled icemakers – follow steps 7.1 through 7.4. Ice transport tube Potable water and drain lines ➋ ➊ • Slide icemaker into louvered docking ➊...
Page 17
Water-cooled icemakers – follow steps 7.5 through 7.10. Cooling lines Ice transport tube ➋ ➊ • Install icemaker cooling water lines to • Slide icemaker into louvered docking ➊ louvered docking assembly assembly • Insert ice transport tube into coupling and ➋...
Page 18
7.10 Power cord Power cord • Remove twist tie • Position plate into opening and secure with supplied screw • Carefully pass plug thru opening and plug into wall outlet HARMONY • RIDE Technology self-contained...
Front cover Install front cover to icemaker. Normal front cover installation Front cover installation – undercounter CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. Failure to do so could result in damage to equipment. • Slide icemaker cover over machine, •...
Page 20
• Maximum length of transport tube for Micro Chewblet applications is 10’ (3 m). Horizon, RIDE, and Harmony are trademarks of Follett Corporation. Follett and Chewblet are registered trademarks of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 •...