Table of Contents
Advertisement
Power amplifier section:
Rated power and load:
80 Watts RMS into 4 Ohms (with DDT
compression)
Frequency response:
+0, -3 dB, 20 Hz to 20 kHz @ 80 Watts
RMS into 4 Ohms
Total harmonic distortion:
Less than 0.3%, 1 Watt to 80 Watts RMS,
20 Hz to 20 kHz, 4 Ohms
DDT
dynamic range:
™
Greater than 20 dB
DDT maximum THD:
Below 0.8% THD for 6 dB overload
Below 3.5% THD for 20 dB overload
Hum and noise:
Greater than 83 dB below rated power
Power consumption:
200 Watts, 50/60 Hz, 120 VAC (domestic)
Preamp section:
The following specs are measured @ 1kHz
with the controls preset as follows:
Master gain @ 10
Low EQ @ 0 dB
Mid EQ @ 0 dB
Mid Shift @ 600 Hz
High EQ @ 0 dB
Presence EQ @ 0 dB
Reverb @ 0
Nominal levels are with pre gain @ 5
Minimum levels are with pre gain @ 10
Preamp high gain input (no pad):
Impedance: High Z, 220 k Ohms
Nominal input level: -29.9 dBV, 32 mV RMS
Minimum input level: -53.2 dBV, 2.2 mV RMS
Maximum input level: 8 dBV, 2.5 V RMS
Warranty registration and information for U.S. customers available online at
Peavey Electronics Corporation
Nashville
SPECIFICATIONS
Preamp Low Gain Input (-10 dB pad):
Impedance: High Z, 68k Ohms
Nominal input level: -19.9 dBV, 101 mV RMS
™
Minimum input level: -43.2 dBV, 6.9 mV RMS
Maximum input level: 18 dBV, 8 V RMS
Pre EQ patch send:
Load impedance: 10k Ohms or greater
Nominal output level: -18.6 dBV, 117 mV RMS
Pre EQ patch return:
Impedance: High Z, 220 k Ohms
Designed Input Level: -18.6 dBV, 117 mV RMS
(Switching jack provides send to return
connection when not used)
Post EQ patch send:
Load impedance: 10 k Ohms or greater
Nominal output level: -14.1 dBV, 198 mV RMS
Post EQ patch return:
Impedance: High Z, 1 m Ohms
Designed Input Level: -14.1 dBV, 198 mV RMS
(Switching jack provides send to return
connection when not used)
XLR line output:
Load impedance: 5 k Ohms or greater
Nominal output level: -3.1 dBV, 0.7 V RMS
Preamp output / CD input:
Load impedance: 10 k Ohms or greater
Nominal output level: -3.1 dBV, 0.7 V RMS
Nominal CD Input Level: -3.1 dBV, 0.7 V RMS
(Stereo cable must be used for CD Input
to function)
Power amp input:
Impedance: High Z, 27 k Ohms
Designed Input Level: -3.1 dBV, 0.7 V RMS
(Switching jack provides preamp output
to power amp input connection when not
used)
www.peavey.com
www.peavey.com/warranty
or use the QR tag below
10
Features and speci cations subject to change without notice.
5022 Hartley Peavey Drive
Meridian, MS 39305
Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005
112
™
System hum and noise @ nominal input
level:
(20 Hz to 20 kHz unweighted)
Greater than 75 dB below rated power
Equalization:
Low: +/-15 dB @ 45 Hz, shelving
Mid: +/-15 dB @ Mid Shift frequency,
boost/cut
Mid Shift: 150 Hz to 1.5 kHz
High: +/-15 dB @ 6 kHz (special EQ)
Presence: +/-15 dB @ 10 kHz, shelving
External footswitch (part #03022910,
not included) functions:
Select effects: Post EQ effects Loop defeat
Reverb: Reverb defeat
Dimensions (H x W x D):
18.125" x 21.375" x 10.250"
Weight:
42.3 lbs.
(601) 483-5365
FAX (601) 486-1278
Advertisement
Table of Contents
