Page 1
April 15, 2021 Lit. No. B64092, Rev. 09 Models 760TR, 810TR, 8100TR, 860TR, 8600TR & 8611TR Installation Instructions & Owner's Manual Original Instructions CAUTION See your BLIZZARD sales outlet/website for ® specifi c vehicle application recommendations before installation. CAUTION Read this document before installing the snowplow.
PREFACE AUTHENTIC PARTS AND ACCESSORIES Congratulations on purchasing the most advanced Your BLIZZARD snowplow is a valuable investment. snowplow available! The POWER PLOW™ snowplow The best way to assure original equipment reliability is clearing new trails for innovative design, rugged and effi...
SAFETY SAFETY DEFINITIONS WARNING/CAUTION & INSTRUCTION LABELS WARNING Become familiar with and inform users about the Indicates a potentially hazardous situation warning and instruction labels on the back of the that, if not avoided, could result in death or blade. serious personal injury.
Page 6
SAFETY Blade Serial Number Label WARNING Do not exceed vehicle operative Blizzard capacity including the blade. See PO BOX 245038 Milwaukee, WI 53223 vehicle rating label. NNNNNNNNNNNNNNNNNNNNNNNNNNNN YYMMDDLLXXXXZZZZZ YYMMDDLLXXXXZZZZ WARNING Never stand, work or reach under lift arms or lift cylinders without employing a lift arm stop or stand.
Page 7
Store only in approved containers away from sources of heat or fl ame. Size Blade Assembly Wt (lb) Wt (kg) 7'6" 760TR CELL PHONES 8100TR 1132 A driver's fi rst responsibility is the safe operation of 8'6" 8611TR 1728 the vehicle.
OPERATION – 810TR, 8100TR & 8611TR MODELS Your POWER PLOW™ snowplow is the most WARNING advanced and versatile snowplow on the market. Never use the snowplow attachment to carry The snowplow blade and wings can be adjusted into people, as a man lift or as a work platform. an infi...
OPERATION – 760TR, 860TR & 8600TR MODELS Your SPEEDWING™ snowplow is the newest WARNING multi-position snowplow on the market. The snowplow Never use the snowplow attachment to carry blade can be adjusted into a variety of plowing people, as a man lift or as a work platform.
UNPACKING & INSPECTION Your snowplow has been packaged to withstand Once you have inspected all parts and removed all transit and weather related damage. Fully inspect packaging materials, your snowplow is ready to be all components upon receipt of your snowplow. fully assembled.
TORQUE SPECIFICATIONS TORQUE CHART CAUTION Read instructions before assembling. Fasteners should be fi nger tight until instructed to tighten according to the torque chart. Use standard methods and practices when attaching snowplow including proper personal protective safety equipment. Grade Identifi cation for J429–Grade 5 Bolt Grade Identifi...
Page 12
TORQUE SPECIFICATIONS 37° JIC Flare Torque Values ft-lb Turns Size Assembly Steps min–max 6–7 1. Make sure that the tubing and threads are clean. 8–9 2. Lubricate the threads with 10W hydraulic fl uid. 11–12 3. Hand tighten the nut/sleeve to approximately 30 in-lb. 14–15 4.
MOLDBOARD & A-FRAME ASSEMBLY – 810TR, 8100TR & 8611TR MODELS 1. Remove dust cap from both of the slide box 3. Position the front (top) hole in the A-frame with the cylinders located at the center/rear of the middle hole in the pivot beam. Insert cap screw moldboard.
MOLDBOARD & A-FRAME ASSEMBLY – 810TR, 8100TR & 8611TR MODELS 5. Position the pivot beam between the two Hook each extension spring to the receiving holes support ribs until the connecting points on the on the pivot beam and attach the opposite end of beam align with those on the snowplow.
Page 15
MOLDBOARD & A-FRAME ASSEMBLY – 810TR, 8100TR & 8611TR MODELS 9. Assemble the manifold. Each of the hose ports on NOTE: When handling the manifold, hold the the manifold is covered with stretch wrap. Remove manifold at the sides of the block. Never handle the wrap and install adapter (56695) in ports #1, 2, the manifold by coils.
MOLDBOARD & A-FRAME ASSEMBLY – 760TR, 860TR & 8600TR MODELS 1. Position the front (top) hole in the A-frame with For 8600TR model: Insert one bushing (42410) the middle hole in the pivot beam. Insert cap through each mounting hole and secure it with a screw (B61331 for 760TR;...
Page 17
MOLDBOARD & A-FRAME ASSEMBLY – 760TR, 860TR & 8600TR MODELS 9/16" 9/16" 3/4" 9/16" 25/32" 17/32" 9/16" 40571 B60403 B60539 • Angle Cylinders • Angle Cylinders • Manifold Ports 4. Hook each extension spring to the receiving holes 5. Install the blade guides at each end of the...
Page 18
MOLDBOARD & A-FRAME ASSEMBLY – 760TR, 860TR & 8600TR MODELS 6. Assemble the manifold. Each of the hose ports on 10. Reinstall A-frame cover by aligning the holes in the manifold is covered with stretch wrap. Remove the cover with those on the A-frame and securing the wrap and install adapter (B60403) in both it with 3/8"...
1700 PSI 1700 PSI (2800 PSI) (2800 PSI) NOTE: 760TR, 860TR, and 8600TR models have no solenoids and require no electrical connections between the tractor and the snowplow. One hose from each angle cylinder connects to the 760TR NOTE: Where applicable, Model 8611 values are in and 860TR manifolds to provide wing pressure parentheses.
NOTE: 760TR, 860TR, and 8600TR Models have only one relief valve (PN B60168 – 3000 psi) and no solenoids. One hose from each angle cylinder connects to the 760TR and 860TR manifolds to provide wing pressure relief. Lit. No. B64092, Rev. 09...
If welding "P3" on 810TR and 8611TR models; from angle the tractor-specifi c hooks is necessary, measure rams on 760TR, 860TR, and 8600TR models) the distance on the tractor to determine appropriate through the clamp on left side of oscillating plate.
ELECTRICAL INSTALLATION – 810TR, 8100TR & 8611TR MODELS 2. Connect the tractor end of the coil harness to the NOTE: 760TR, 860TR, and 8600TR models do not tractor's auxiliary electrical system according to require electrical connections between the tractor the vehicle's owner's manual or service manual.
MOUNTING & DISMOUNTING INSTRUCTIONS – ALL MODELS Prior to operating your snowplow, review the Mount NOTE: If at any time the Mount and Dismount and Dismount Instructions label on the back of the Instructions label, or any other label attached driver-side moldboard.
Consult your tractor's owner's manual for the For 760TR, 860TR, and 8600TR Models: Angle appropriate couplings needed. the blade left and right a few times. For 810TR and 8611TR Models: Connect the...
ADJUSTABLE SNOWPLOW SHOE ASSEMBLY – ALL MODELS WARNING Blade can drop unexpectedly. Place the blade on jack stands. Failure to do so could result in serious personal injury. With the snowplow fully assembled and operational, 5/16" install the adjustable plow shoes. Locknut 5/16"...
Check hoses for wear and leaks. Check cylinders for leaks; inspect rod ends for corrosion & pitting. Check cables for wear or fraying (760TR and 860TR models only). Lubricate all exposed cylinder rod ends with liquid white lithium grease to prevent corrosion.
REMOVING FROM STORAGE & LIFTING REMOVING FROM STORAGE LIFTING 1. Perform all regular maintenance. To lift and move this snowplow, attach chain fall grab hooks to outside pivot beam area shown. 2. Replace the hydraulic fl uid in the hydraulic system. Always follow recommended lift warnings and Prolonged storage could result in condensation procedures.
BLIZZARD snowplow, contact one of our authorized Blizzard does not recommend repairs by other than ® outlets for repair information, or visit us online at our authorized outlets. Failure to use an authorized www.blizzardplows.com.
MOLDBOARD & WING PARTS – 810TR & 8611TR MODELS Groove * Current ram has a groove around the base near the pin hole. Early ram does not have a groove. Item Part 810TR 8611TR Description B61681 Pin, Wing Stop B11989 5/8 x 11-1/2 Pin, Hydraulic Cylinder Base End –...
MOLDBOARD & WING PARTS – 8100TR MODEL * Current ram has a Groove groove around the base near the pin hole. Early ram does not have a groove. Item Part Qty Description 41173 Moldboard 59900 Label – Warning, Information B63160 Label –...
Page 35
MOLDBOARD & WING PARTS – 8100TR MODEL Item Part Qty Description B61030 1/8 x 2-5/8 Hair Cotter Pin B61198 5/8 ID x 3/4 OD x 1 Black Vinyl Cap B55066 Slide Box – PS B51047 Wing Cutting Edge – PS 96326 Label –...
A-FRAME & PIVOT BEAM PARTS – 810TR & 8100TR MODELS Tractor-Specific Hook Mounts Groove * Current ram has a groove around the base near the pin hole. Early ram does not have a groove. Lit. No. B64092, Rev. 09 April 15, 2021...
Page 43
A-FRAME & PIVOT BEAM PARTS – 810TR & 8100TR MODELS Item Part 810TR Description B52151 Pivot Beam 95739 3/4 x 5 Clevis Pin B50069 3/4 x 3 Clevis Pin B50071 3/4 x 3-41/64 Clevis Pin 40571 Elbow, 90° –6 M JIC/–6 M ORB B60029 Hydraulic Cylinder, Snowplow Angle (early ram –...
A-FRAME & PIVOT BEAM PARTS – 8611TR MODEL Tractor-Specific Hook Mounts Groove * Current ram has a groove around the base near the pin hole. Early ram does not have a groove. Lit. No. B64092, Rev. 09 April 15, 2021...
Page 45
A-FRAME & PIVOT BEAM PARTS – 8611TR MODEL Item Part 8611TR Description 95739 3/4 x 5 Clevis Pin B41077 Pivot Beam 40571 Elbow, 90° –6 M JIC/–6 M ORB B60324 Hydraulic Cylinder, Snowplow Angle (Early ram – see callout on diagram.) 43805 Ram Assembly 2 x 10 (Current ram –...
A-FRAME & PIVOT BEAM PARTS – 760TR, 860TR & 8600TR MODELS Tractor-Specific Hook Mounts Groove * Current ram has a groove around the base near the pin hole. Early ram does not have a groove. Lit. No. B64092, Rev. 09...