Motor Specifications; Grounding Instructions - Delta UNISAW 36-L336 Instruction Manual

F. Push the workpiece past the saw blade prior to release.
G. Never rip a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.
H. Never saw a large workpiece that cannot be controlled.
Never use the fence as a guide or length stop when crosscutting.
I.
J. Never saw a workpiece with loose knots, flaws, nails or other foreign objects.
K. Never rip a workpiece shorter than 10" (254 mm).
L. Never use a dull blade – replace or have resharpened.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals:
work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear
protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury.
Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and
body. Always operate tool in well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines:
FOR THREE HORSEPOWER, SINGLE PHASE UNITS
A suitable circuit should not be less than AWG12/3 wiring where the ground wire is attached to an earth ground. The circuit should be
protected by a circuit breaker or time delay fuse.
FOR FIVE HORSEPOWER, SINGLE PHASE UNITS
The circuit should not be less than #10 wire and should be protected with a 40 Amp time delay fuse.
NOTE: Time delay fuses should be marked "D" in Canada and "T" in the US. If an extension cord is used, use only 3-wire extension
cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine's plug. Before connecting
the machine to the power line, make sure the switch is in the "OFF" position and be sure that the electric current is of the same
characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage
the machine.
SHOCK HAZARD. Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

All Unisaw motors are rated for 60 HZ alternating current, but voltage and HP varies according to model:
Model: Specifications:
36-L336, 36-L352 3HP, 230V single phase motor
36-L552
5 HP , 230V single phase motor
36-L552LVC 5 HP , 230V/460V three phase, dual votage motor
Before connecting the machine to the power source, make sure that the switch is in the "OFF" position.

GROUNDING INSTRUCTIONS

SHOCK HAZARD. This machine must be grounded while in use to protect the operator from electric shock.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of
electric shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having
an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instruction are not completely understood, or if in doubt as to
whether the machine is properly grounded.
SAVE THESE INSTRUCTIONS
6